manualshive.com logo in svg

Rockwell Automation MSR300, Instruction Manual, Page: 69 / 85

Share
Download
Rockwell Automation MSR300 Instruction Manual Download Page 69

   

MSR300 Safety System Manual   

 

 
Rockwell Automation  

 

MSR300 Manual.doc 

Pg 69 of 85 

 

9 

Serial Data Communication: Details 

 

The MSR310 is equipped with two RS232 serial data interfaces: one can be used in bi-
directional, the other in uni-directional mode.

 

 
 

9.1 

Serial Data Interface Connections 

 
The serial interface connections are illustrated below. 
 

TxD1

RxD1

GND

RS-232

Bi-

directional

TxD2

GND

RS-232

Uni-

directional

 

 
 

9.2 RS232 

Bi-directional 

 
Bi-directional RS232 features automatic baud rate detection, and can handle baud rates 
of 2400, 4800, 9600, or 19200 baud. 
 

9.2.1 Protocol: 

 
Supported exception codes: 
 

Code Name 

Meaning 

0x01 

Illegal function 

The function code is not supported by the 
MSR310 

0x02 

Illegal data address 

The data address in the query is not allowed 
for the MSR310 

0x03 

Illegal Data Value 

The data value in the query is not valid 

 
Supported functions: 
 

Code Name 

Meaning 

0x03 Read 

Multiple 

Registers 

Reads the contents of a sequence of registers 

0x06 Write 

Single 

Register 

Writes a value to a single register. 
 

 
 

 
 
 
 
 

Summary of Contents for MSR300






















































































Reviews:

No comments