manualshive.com logo in svg

Rockwell Automation MSR300, Instruction Manual, Page: 52 / 85

Share
Download
Rockwell Automation MSR300 Instruction Manual Download Page 52

   

MSR300 Safety System Manual   

 

 
Rockwell Automation  

 

MSR300 Manual.doc 

Pg 52 of 85 

 

7 Installation, 

Start-Up, 

Operation, Maintenance 

 
 
7.1 

Safety Precautions and Practices 

 
 
 
 
 
 
 

 
 
 
 

 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Use this product only for intended applications: 

The MSR300 Safety System is intended for applications requiring 
safety monitoring of machinery in accordance with the following 
directives / standards: 

•

  EN954-1: Safety-Related Parts Of Control Systems. 

•

  IEC 61508: Functional Safety of Electrical / Electronic / 

Programmable Electronic Safety-Related Systems, Parts 1-7, 
1998. 

This equipment must not be used for unintended applications, nor in 
ways that do not conform to appropriate safety standards and good 
practices. The safety functions may not operate properly (or at all) if 
this equipment is not used for the intended purposes. 

 

Installation and operation to be done only by qualified technical 
personnel:  

This equipment is to be installed, started up, and operated only by 
technical personnel who have been trained and made familiar with: 

•

  The product/s for which this document exists 

•

  Directives, regulations and practices relating to machine safety 

•

  Instrumentation and automation components, equipment and 

systems 

•

  Industrial electrical practices 

 

Uptodate user documentation must readily accessible by 
technical personnel:  

The latest version of user documentation that includes instructions for 
installation, operation and maintenance of this product must be 
readily available near at hand to personnel involved in any of these 
tasks.  

 

Identify hazardous areas and dangerous operating modes 
before using: 

Machine safety applications make it necessary for hazardous areas 
and dangerous operating modes to be carefully identified, and 
adequate measures taken to ensure that failure or tampering does 
not allow automated equipment to be of risk to personnel. 

 

Use within specified operating limits: 

This product, the equipment on which it installed, persons handling 
the product and equipment, and/or the immediate environment can 
be harmed if this equipment is operated outside the specified limits of 
any of its technical parameters.  

Summary of Contents for MSR300






















































































Reviews:

No comments