manualshive.com logo in svg

Robomow MC150, Operating Manual

Share
Download
Robomow MC150 Operating Manual Download Page 41

41

Display

Message / Description

Action Required

U024

Keep charging if not used.

Displayed only if the mower is disconnected from 

a Charging Adaptor.

It is recommended to keep the mower connected 

to the Power Supply when not in use.

U025

Switch Off before lifting

It is required to switch Off the System Switch 

before lifting and carrying the mower.

U029

Change the wires in plot connector

Displayed during the One-Time Setup.

Swap the wires at the plot connector.

Refer to section 5.2.4 in the User Manual.

U032

Switch on the System Switch.

Displayed if the mower is connected to charging, 

but the System Switch is ‘Off’.

Switch the System Switch to ‘On’.

U041

Press the STOP button at Sub-Zone entry.

Displayed only when using the Robomow App to 

add a Sub-Zone.

Press STOP at the point you want the mower to 

start mowing the Sub-Zone.  

U042

Learning edge distance.

Displayed only when using the Robomow App.

The mower learns the distance of the Perimeter 

Wire in a Separated Zone. Press STOP to learn he 

distance.

U043

Going to Sub-Zone entry point.

Displayed only when using the Robomow App.

Press OK to continue the process of adding a Sub-

Zone.

U044

Place the mower in the Base Station.

Displayed only when using the Robomow App.

Place the mower in the Base Station before 

starting the process of adding a Sub-Zone.

U051

Reposition the Base Station position.

Displayed during the One-Time Setup.

Refer to section 5.2.4 in the User Manual.

U052

Adjust Wire

Refer to section 5.2.5 in the User Manual.

U062

An alarm will soon be activated.

This message warns you to enter the PIN code 

before the Anti-Theft alarm will sound.

U064

The Searching Base Station operation cannot be 

performed

When choosing the ‘Home’ button in a zone 

without a Base Station.

U086

Waiting for the signal…

Robomow has stopped the operation. It does not 

detect a signal.

Check the power to the Power Box.

There may be an electrical power interruption. 

There is no need to do anything. Robomow will 

renew operation as soon as the power is back on.

U087

Mow motor overheat, Cooling…

The mowing motor has been working under a 

severe load for too long.

No need for action – Robomow will renew 

automatically the operation, as the mowing motor 

will cool down.

U088

Drive motor overheat, Cooling…

The drive motors have been working under a 

severe load for too long.

No need to do anything. 

Robomow will renew the operation automatically 

as soon as the drive motor will cool down.

Summary of Contents for MC150



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands