background image

12

Types of Separated Zone setups:

 

A Separated Zone smaller than 100 m² (1100 ft²)

Separated area that is smaller 

than 100m² (1100 ft²) can be 

covered in a single operation, 

thus, if possible, the separated 

area may be connected to the 

main area’s Perimeter Wire 

(have the signal come from the 

Main Base Station).

Or

It may have to have its own 

separate Perimeter Wire.

In that case, it will have to 

be connected to a Perimeter 

Switch (optional accessory – 

see Chapter 12 - Accessories).

Or:

A Separated Zone larger than 100 m² (1100 ft²)

If a separated area is larger than 

100m² (1100 ft²), then it requires 

more than a single operation to 

cover the area; 

In such cases, an additional 

Base Station (optional accessory) 

should be installed in the 

Separated Zone, otherwise 

you will have to manually bring 

the mower several times to the 

Separated Zone in order to 

complete the mowing of the area.

3.2 

Select Base Station Location

3.2.1  Base Station Location Guidelines

 

Do not

 

place the Base Station within  

3 meters (10 ft.) after a corner (relevant for Internal 

setup only (section 3.3.2).

 

The Base Station should be within 15m (50 ft.) of a 

power outlet (230V / 120V).

 

If the lawn has more than one zone, place the Base 

Station within the largest zone.

 

Make the Base Station invisible to the street to 

avoid theft.

 

Select a shady spot. This will extend battery lifetime.

 

Place the Base Station on a relatively level ground. 

Do not place it on a slope.

 

Place the Base Station away from sprinkler heads.

Separated Zone Smaller than 100m

(1100ft

2

)

2 Wires under 

same peg

Base Station

Separated Zone Smaller than 100m

(1100ft

2

)

Optional Power Box 

& Base Station

Main zone Power Box & 

Base Station

Min. 3m (10ft)

from any corner

Summary of Contents for MC150



















































Reviews: