Robomow MC1000 Original Operating Instructions Download

Page: 38 / 52

Charging

8.1

Charging During the Season

The Base Station is the primary charging source when Robomow is docked and will maintain the optimal battery

charge while awaiting departure.

8.2

Charging Out of Season

During out of season months, such as winter, it is required to:

•

Fully charge the battery in the Base Station till

the Battery indicator is green and lit constantly.

Note! The Safety Switch should be in ‘On’

position during charging.

LED indicators for charging:

Red is lit constantly – Charge the battery.

Green is blinking – During battery charging.

Green is lit constantly – Battery is fully charged.

•

Remove Robomow from its Base Station. Turn

the Safety Switch off and store the mower in a

room temperature.

•

If the mower is stored for more than 3 months,

it is required to recharge the battery every 3

months till the Battery indicator shows it is fully

charged.

•

The charging can be done in one of the following

options:

Place the mower in the Base Station for charging.

Connect Robomow directly to the Power Box as follows:

Disconnect the DC Cable coming from the Power Box

to the 15m Extension Cable and connect it to the rear

side of the mower as shown in the figure to the right.

•

Once the season starts, just place Robomow in

its Base Station to begin automatic operation.

IMPORTANT

Always charge your mower in a horizontal position. The mower should be flat on the

ground while connected to the Power supply.

Troubleshooting and User Messages

9.1

General Error Codes

Robomow continuously monitors its operation. It produces error codes to assist you in running it smoothly.
A sticker containing the most common error codes is provided in the box. You can place it on the mower for your

convenience.

E9* (See Troubleshooting in Manual) represents

stops and error that are not very common, and

thus they are not shown in the above Error Code

Table. If E9 is displayed, press the RIGHT arrow

to receive the Error Code reason, for which

the mower has stopped and refer to the User

Manual for more details.

•

Usually, if the mower stops, an error code is

displayed. This display stays on for 5 minutes. If

you arrive later than those 5 minutes, the display

will be blank.

•

To wake Robomow up and see the last error

code displayed prior to stopping, press the OK

button on the mower.

Robomow Error Codes Table

E 1

Stuck in Place

E 2

Mower is Outside

E 3

No Wire Signal

E 4

Check Power

E 5

Check Blade / Cutting Height

E 6

Check Drive

E 7

Front Wheel Problem

E 8

Decrease Inactive Time

E 9*

See Troubleshooting in Manual

E5XX

Call Support

Summary of Contents for MC1000





















































Search results

Summary of Contents for MC1000

Reviews:

Related manuals for MC1000

Brands by name

Popular brands

Robomow MC1000, Original Operating Instructions

Search results

Summary of Contents for MC1000

Reviews:

Related manuals for MC1000

Brands by name

Popular brands