Robomow MC1000 Original Operating Instructions Download

Page: 6 / 52

1.4

Robomow Safety Features

Child Lock

The Child Lock prevents unintended operation of Robomow

by an accidental press of one of the buttons. Only

pressing of two buttons in a certain order will initiate the operation.

Anti-Theft / Disabling Device

The Anti-Theft/Disabling Device system provides the user a disabling function that will prevent anyone from using or

driving the Robomow

unless they have the valid code to enter. You will be prompted to enter a four digit code of your

choice to use as your personal security code.

Lift Sensor

In the event the mower is raised from the ground during blade operation, the blade will stop rotating immediately.

Tilt Sensor

In case the mower is tilted up towards a vertical position, the blade will stop immediately.

Obstruction Sensor

Robomow detects when there is an obstacle in its way during operation. When the mower collides with an obstacle,

the mower will stop the rotation of the blade immediately, will stop movement in that direction and reverse itself away

from the obstacle.

Emergency Stop Button

Pressing the STOP button at any time during operation will stop the mower and the blade immediately.

Safety Switch

Switching off the Safety Switch will prevent any operation of Robomow

. It is required to switch it off before lifting

Robomow

and before any maintenance is done.

Sealed Batteries

The batteries that operate Robomow

are completely sealed and will not leak any type of fluids, regardless of position.

Base Station / Perimeter Switch and Perimeter Wire

Robomow

cannot operate without a Perimeter Wire installed and activated through the Base Station / Perimeter

Switch. In the event the Perimeter Switch is turned off or otherwise fails to function, Robomow

will stop operating.

Summary of Contents for MC1000





















































Search results

Summary of Contents for MC1000

Reviews:

Related manuals for MC1000

Brands by name

Popular brands

Robomow MC1000, Original Operating Instructions

Search results

Summary of Contents for MC1000

Reviews:

Related manuals for MC1000

Brands by name

Popular brands