Robomow MC1000 Original Operating Instructions Download

Page: 46 / 52

10.

Product Specification

RC 304

RC 306

RC 312

Designation

Robotic Mower

Max Lawn Size

400 m² / 4400 ft²

600 m²/ 6600 ft²

1200 m²/ 13000 ft²

Base Station

Included

Robot Dimensions

63x46x21cm/25x18x8”

Package Dimensions

80x54x33cm/32x21x13” 80x54x33cm/32x21x13” 80x54x33cm/32x21x13”

Robot Weight

11.1 kg / 24.5 lb.

Package Weight

22.8 kg/ 50.5 lb.

22.8 kg / 50.5 lb.

Cutting Width

28 cm/ 11”

28 cm / 11”

Cutting Height

15-60 mm/ 0.6”-2.4”

15-60 mm / 0.6”-2.4”

Mowing Power

200 Watts

Mowing Motors

DC Brush

DC Brushless

Noise Level

High Power: 67.6 dB measured (Guaranteed 69 dB)

The noise at the operator’s ears less than 70 dB

Battery Type

26V Lithium (LiFePO4)

Robot Part No.

PRD7004B

PRD7006B

PRD7012A

Anti-Theft / Disabling Device PIN Code

Write down your 4-digit Anti-Theft / Disabling Device PIN code.

Refer here, if you ever forget the code.

Robomow Serial Number

SIDE

BOTTOM

Summary of Contents for MC1000





















































Search results

Summary of Contents for MC1000

Reviews:

Related manuals for MC1000

Brands by name

Popular brands

Robomow MC1000, Original Operating Instructions

Search results

Summary of Contents for MC1000

Reviews:

Related manuals for MC1000

Brands by name

Popular brands