Robin America EH72 Service Manual Download Page 44

Page: 44 / 74

– 40 –

25) ADJUST GOVERNOR SYSTEM

(1) Push speed control lever all the way to the high

speed position and fix it by tightening nut.

(2) Check that governor lever is pulled by governor

spring and carburetor throttle valve is fully open.

(3) Turn governor shaft counterclockwise all the

way and tighten lock bolt to secure the lever on

the shaft.

26) BLOWER HOUSING

Attach blower housing to crankcase.

27) FUEL PUMP

Install fuel pump onto #2 cylinder baffle.

Connect fuel pipe between carburetor and fuel

pump.

28) AIR CLEANER

(1) Connect breather pipe to air cleaner base.

(2) Fit air cleaner base onto carburetor.

(3) Connect breather pipe to #1 cylinder head.

(4) Set air cleaner element along with urethane

foam onto base.

(5) Install air cleaner cover with knob.

GOVERNOR LEVER

GOVERNOR SHAFT

Fig. 5-50

FUEL PUMP

Fig. 5-51

AIR CLEANER BASE

Fig. 5-52

Summary of Contents for EH72










































































Search results

Summary of Contents for EH72

Reviews:

Related manuals for EH72

Brands by name

Popular brands

Robin America EH72, Service Manual

Search results

Summary of Contents for EH72

Reviews:

Related manuals for EH72

Brands by name

Popular brands