16
&RQ¿JXUDWLRQ
SSID:
mynetwork
0 1 2 3 4 5 6 7
8 9 . _ - @ ,
a b c d e f g h
i j k l m n o p
q r s t u v w x
Network settings
Please wait
Connecting...
Network wizard
PBC Wlan setup
View settings
Wlan region
Manual settings
NetRemote PIN Setup
Network settings
Connection type
Wired
Wireless
IP settings
IP address
192 . 168 . 1 . 25
Subnet mask
255 . 255 . 255 . 0
0DQXDOQHWZRUNFRQ¿JXUDWLRQ
,I\RXGRQRWZLVKWRXVH'+&3IRUDXWRPDWLFQHWZRUNFRQ¿JXUDWLRQRULI\RXUQHWZRUNLVFRQ¿JXUHGZLWKD
hidden SSID, then you will need to enter some network settings manually. The typical user will not need to
XVHPDQXDOQHWZRUNFRQ¿JXUDWLRQ7KHIDFLOLW\LVSURYLGHGWRDOORZWKHSURGXFWWREHXVHGZLWKQHWZRUNVZKHUH
WKHFRQ¿JXUDWLRQRIGHYLFHVLVQRWPDQDJHGE\WKHURXWHURUZKHUHFXVWRPLVHGVHWWLQJVPD\EHUHTXLUHG,Q
VXFKFDVHVLWLVDVVXPHGWKDWWKHXVHUDOUHDG\KDVVXI¿FLHQWNQRZOHGJHWRXQGHUVWDQGWKHWHUPVDQGVHWWLQJV
used for this purpose. IPv4 address schemes are used.
1. From the radio's Network Settings menu, select
'Manual settings'
. You must then choose whether to
connect using
'Wired'
or
'Wireless'
connections. If you choose
'Wireless'
there are as many as nine settings
screens, shown by the
'1 of 9'
progress marker in the top right corner of the display. If you choose
'Wired'
WKHUHDUH¿YHVFUHHQVDQGWKHSURJUHVVPDUNHUZLOOUHÀHFWWKLVDOWKRXJKWKHVWHSVWRVHWXSWKHQHWZRUN
parameters are basically the same.
7KHVXEVHTXHQWPHQXVDOORZFRQ¿JXUDWLRQRIWKHIROORZLQJSDUDPHWHUV
DHCP - On or Off
IP address - e.g. 192.168.1.25
Subnet mask - e.g. 255.255.255.0
Gateway adress - e.g. 192.168.1.1
DNS address (primary and secondary addresses)
SSID - needed for WiFi connections if the SSID is not broadcast
WEP / WPA / WPA2 key and settings
When entering numbers, the SSID or the WiFi pass key, the three controls on the right-hand side of the
screen have special functions. You can quickly access these by pressing the
Info
button and then use the
Tuning
control as needed:
select
'
' to erase a character just entered (long press to clear);
Info
again to continue
select
'
' when the complete encryption key has been entered
select
'
' to cancel and go back to the TKIP / AES options screen
3. Upon completion of the settings the radio should connect to the network. If the connection is made
successfully, the radio will return to the Network Settings menu. If the unit cannot connect, then it will display
a
'Failed to connect'
message. You will then need to identify which setting may need to be changed, or
whether some other network issue is responsible. Once connected, the network settings are saved. They
are retained in memory while the radio is disconnected from the mains.
