Robe CitySkape Xtreme Page 24 User Manual Download | Manualshive

Page: 24 / 24

background image

CitySkape Xtreme (RGBW)

24

11. Cleaning and maintenance

DANGER !

Disconnect from the mains before starting any cleaning or maintenance work

Rinse off loose dirt with low pressure water spray. Wash the housing with a soft brush or sponge and a mild, non-
abrasive washing detergent. Rinse it.
There are no serviceable parts inside the device.
Maintenance and service operations are only to be carried out by a qualified person.
Should you need any spare parts, please use genuine parts.

If the power supply cable of this device will be damaged (cable firmly connected with the device), it has to be
replaced by authorized distributors only in order to avoid hazards.

Specifications are subject to change without notice.

June 2, 2011

«
...
22
23
24

Summary of Contents for CitySkape Xtreme

























Reviews:

No comments

Related manuals for CitySkape Xtreme

SENTINEL 2 LIGHTS SPOT LIGHT

Brand: Lucci Fresco Pages: 2

Brand: ARRI Pages: 6

DL-PAR105 SMD LED Spot 1292337

Brand: Renkforce Pages: 92

Brand: CONCORD Pages: 3

Brand: Larson Electronics Pages: 4

Spotlight DP0755

Brand: Davey Lighting Pages: 2

SPORTSPOT VEC189

Brand: Vector Pages: 6

Brand: VELAMP Pages: 16

2Bright Expo 575 WW

Brand: Ignition Pages: 36

Brand: LIVARNO LUX Pages: 138

Brand: Sealey Pages: 2

Power Products LED437

Brand: Sealey Pages: 3

Brand: Theben Pages: 17

Brand: West Marine Pages: 2

Brand: Ryobi Pages: 81

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands