RMG USZ 08 series, Operating Instructions Manual, Page: 48 / 70

USE 09 MEASURED VALUES AND PARAMETERS
...............................................................................................................................................................................................................
...............................................................................................................................................................................................................
Manual USZ 08 · EN05 · 2015-06
43
I-06 C c-out select 2158 I Current output, selection of the measured value (Modbus reg.)
I-07 C c-out mode 2159 M Current output, operating mode ( OFF , SET VALUE, 0-20mA, 4-20mA)
I-08 C c-out err mode 2160 M Current output, operating mode if a fault occurs ( OFF , MIN, MAX)
I-09 C c-out damping 1380 F Current output, damping (0.0=OFF, 1.0=max)
I-10 E c-out gradient 1382 F Current output, gradient
I-11 E c-out offset 1384 F Current output, offset
Serial ports
Value Unit Modbus Description
J-12 N DZU-0 address 2283 I Serial interface -0 DZU slave ID (ASCII: 00-99)
J-13 A serial-0 status 760 T Serial interface -0, status
J-14 N serial-1 mode 2107 M Serial interface -1, mode (OFF,
IGM
, USE09, DZU, DZU-DIAG, DZU
X-FRAME, VO)
J-15 N serial-1 baud rate baud 2108 M Serial interface -1, baud rate (2400, 4800, 9600, 19200, 38400 , 57600)
J-16 N serial-1 bits 2109 M Serial interface -1, number of bits (7, 8 )
J-17 N serial-1 parity 2110 M Serial interface -1, parity ( NONE , EVEN, ODD)
J-18 N not available 2286 M Serial interface -1 Modbus operating mode (not yet available)
J-19 N not available 2287 M Serial interface -1 Modbus hardware (not yet available)
J-20 N not available 2288 I Serielle Schnittstelle -1 Modbus address (not yet available)
J-21 N not available 2289 I Serial interface -1 Modbus register offset (not yet available)
J-22 N not available 2290 I Serial interface -1 Modbus turn-off time (not yet available)
J-23 N DZU-1 address 2284 I Serial interface -1 DZU slave ID (ASCII: 00-99)
J-24 A serial-1 status 770 T Serial interface -1, status
J-25 N opt. ser2 mode 2112 M Optional serial interface -2, mode ( OFF , IGM, USE09, MODBUS,
DZU-SLAVE)
J-26 N opt. ser2 baud rate baud 2113 M Optional serial interface -2, baud rate (2400, 4800, 9600, 19200,
38400 , 57600)
J-27 N opt. ser2 bits 2114 M Optional serial interface -2, number of bits (7, 8 )
J-28 N opt. ser2 parity 2115 M Optional serial interface -2, parity ( NONE , EVEN, ODD)
J-29 N Modbus-2 protocol 2178 M Optional serial interface -2, Modbus operating mode (OFF, RTU , ASCII)
J-30 N Modbus-2 hw-mode 2179 M Optional serial interface -2, Modbus hardware (RS232, RS485 )
J-31 N Modbus-2 address 2180 I Optional serial interface -2, Modbus address (ID)
J-32 N Modbus-2 reg.offset 2181 I Optional serial interface -2, Modbus register offset
J-33 N Modbus-2 gap time 2182 I Optional serial interface -2, Modbus gap time
J-34 N long byte order 2251 M Ser-2 Modbus byte order with long: (1,0)(3,2) or (3,2)(1,0) ( Normal ,
SWAPPED)
J-35 N float byte order 2252 M Ser-2 Modbus byte order with float: (1,0)(3,2) or (3,2)(1,0) ( Normal ,
SWAPPED)
J-36 N double byte order 2253 M Ser-2 Modbus byte order with double: (1,0)(3,2)(5,4)(7,6) or
(7,6)(5,4)(3,2)(1,0) ( Normal , SWAPPED)
J-37 N DZU-2 address 2285 I Serial interface -2 DZU slave ID (ASCII: 00-99)
J-38 A serial-2 status 780 T Optional serial interface -2, status
J-39 E DZU interval tics 2111 I Serial interface -1, DZU interval
J-40 N DZU checksum preset 2255 M Serial interface -1, initial DZU checksum value ( 0x00 , 0x7F)