74
User's Guide HDSP AES-32
© RME
30.2 Lock and SyncCheck
Digital signals consist of a carrier and the data. If a digital signal is applied to an input, the re-
ceiver has to synchronize to the carrier clock in order to read the data correctly. To achieve this,
the receiver uses a PLL (Phase Locked Loop). As soon as the receiver meets the exact fre-
quency of the incoming signal, it is locked. This
Lock
state remains even with small changes of
the frequency, because the PLL tracks the receiver's frequency.
If a AES/EBU signal is applied to the HDSP AES-32, the unit indicates LOCK, i. e. a valid input
signal. This information is presented in the HDSP AES-32 Settings dialog. In the status display
SyncCheck,
the state of all clocks is decoded and shown as simple text (No Lock, Lock, Sync).
Unfortunately, LOCK does not necessarily mean that the received signal is correct with respect
to the clock which processes the read out of the embedded data. Example: The HDSP AES-32
is set to 44.1 kHz internally (clock mode Master), and a mixing desk with AES output is con-
nected to the card's AES1 input. The status display will show LOCK immediately, but usually
the mixing desk's sample rate is generated internally (it is Master too), and thus slightly higher
or lower than the HDSP AES-32 internal sample rate. Result: When reading out the data, there
will frequently be read errors that cause clicks and drop outs.
Also when using multiple clock signals, a simple LOCK is not sufficient. The above described
problem can be solved elegantly by setting the HDSP AES-32 from Master to AutoSync (its
internal clock will then be the clock delivered by the mixing desk). But in case the card is
clocked to word clock, this signal can also be un-synchronous, and there will again be a slight
difference in the sample rate, and therefore clicks and drop outs.
In order to display those problems, the HDSP AES-32 includes
SyncCheck
®
. It checks all
clocks used for
synchronicity
. If they are not synchronous to each other, the status display will
show LOCK. If they are synchronous to each other (i. e. absolutely identical) the status display
will change to SYNC. In the example above it would have been obvious immediately that the
entry LOCK is shown in
SyncCheck
instead of SYNC, right after connecting the mixing desk.
With external synchronisation via word clock, both entries Word Clock and AESx must display
SYNC.
In practice, SyncCheck allows for a quick overview of the correct configuration of all digital de-
vices. So one of the most difficult and error-prone topics of the digital studio world finally be-
comes easy to handle.
A special problem occurs with devices offering several AES or SPDIF inputs. While with ADAT
and TDIF all eight channels share the same clock base, with AES there are several completely
independent receivers with their own PLLs and data buffers. Therefore there can be a random
error of ± 1 sample difference between the stereo pairs. The HDSP AES-32 exclusive
SyncA-
lign
®
technology avoids this effect and guarantees sample synchronicity among all four stereo
channels.
Summary of Contents for Hammerfall HDSP AES-32
