User's Guide HDSP AES-32
© RME
41
Thanks to a highly sensitive input stage,
also SPDIF signals can be processed by
using a simple cable adapter phono/XLR.
To achieve this, pins 2 and 3 of a male
XLR plug are connected individually to the
two pins of a phono plug. The cable shield-
ing is only connected to pin 1 of the XLR -
not to the phono plug.
22.2 AES/EBU Outputs
The AES/EBU outputs are provided via 25 pin D-sub connectors with Tascam pinout (also used
by Digidesign). A digital breakout cable will provide 4 male (and 4 female) XLR connectors per
D-sub connector. Each output is transformer-balanced, ground-free and compatible to all de-
vices with AES/EBU ports.
If
Output Format Professional
is chosen, the output level is almost 5 Volt. If deselected, the
output signal will have a channel status compatible to SPDIF. As far as we know, every SPDIF
device should be capable of handling an input signal of up to 5 Volt instead of the usual 0.5
Volt. Nevertheless the output level will be reduced to 2 Volt in this case.
Besides the audio data, digital signals in SPDIF or AES/EBU format contain a channel status
coding, which is being used for transmitting further information. The output signal coding of the
HDSP AES-32 has been implemented according to AES3-1992 Amendment 4:
•
32 kHz, 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz according to the
current sample rate
•
Audio
use
•
No Copyright, Copy permitted
•
Format Consumer or Professional
•
Category General, Generation not indicated
•
2-Channel, No Emphasis or 50/15 µs
•
Single Channel Double Sampling Frequency Mode (Double Wire)
•
Aux Bits Audio use, 24 Bit
•
Origin:
HDSP
Note that most consumer HiFi equipment (with optical or phono SPDIF inputs) will only ac-
cept signals in ‘Consumer’ format!
The status 'Professional' should always be active when sending data to a device with AES/EBU
inputs (when the XLR connectors are used).
Pinout of the D-sub connector, Outputs
Signal Out
1/2+
Out
1/2-
Out
3/4+
Out
3/4-
Out
5/6+
Out
5/6-
Out
7/8+
Out
7/8-
D-Sub
18 6 4 17 15 3 1 14
GND is connected to pins 2, 5, 8, 11, 16, 19, 22, 25. Pin 13 is not connected.
Connecting devices with coaxial SPDIF ports to the HDSP AES-32 outputs is accomplished by
a simple cable adapter XLR/phono, as described above. Just use a female XLR connector.
Summary of Contents for Hammerfall HDSP AES-32
