RKI Instruments 04 Series Operator'S Manual Download

Page: 62 / 98

62 • Chapter 5: User Mode and Calibration

SC-04

7. Press and release POWER MODE to enter the selection and advance to the next number.

To go back a number, press and hold AIR and POWER MODE for a few seconds.

8. Repeat Step 6 and Step 7 to select the remaining numbers. When you press and release

POWER MODE to enter the last number, the password is saved and the instrument returns

to the

PASS-W

item in User Mode.

9. See “Entering Measuring Mode (START)” on page 62 to enter Measuring Mode.

Viewing the ROM/SUM (ROM/SUM)

The

ROM/SUM

screen shows the instrument’s firmware version and firmware checksum.

1. While in User Mode, press AIR to scroll to

ROM/SUM

2. Press and release POWER MODE. The screen shows the ROM/SUM. The ROM is the top

value and the SUM is the bottom value.

3. Press and release POWER MODE to return to the

ROM/SUM

item in User Mode.

4. See “Entering Measuring Mode (START)” on page 62 to enter Measuring Mode.

Entering Measuring Mode (START)

1. While in User Mode, press AIR to scroll to

START

2. Press and release POWER MODE. The instrument begins its warmup sequence.

ROM/SUM

6180

72F8

ROM/SUM

START

Summary of Contents for 04 Series



































































































Search results

Summary of Contents for 04 Series

Reviews:

Related manuals for 04 Series

Brands by name

Popular brands

RKI Instruments 04 Series, Operator'S Manual

Search results

Summary of Contents for 04 Series

Reviews:

Related manuals for 04 Series

Brands by name

Popular brands