background image

SC-04

Chapter 5: User Mode and Calibration • 37

Tips for Using User Mode

To scroll from one item to the next, press and release AIR. To reverse the scrolling 

direction:
a.  Press and hold AIR.
b.  Immediately press POWER MODE and then release both buttons.
c.  The scrolling direction returns to the original direction when you exit and reenter a 

menu.

To skip an item when a question is asked, press and release AIR.

To enter an item and to save any changes, press and release POWER MODE.

To change a flashing parameter, press and release AIR. To reverse the direction of change 

(ie. from increasing to decreasing or vice versa):
a.  Press and hold AIR.
b.  Immediately press POWER MODE and then release both buttons.

To exit an entered item without saving a change, press and hold AIR and POWER MODE 

for a few seconds.

Performing a Bump Test (BUMP)

Bump test the instrument before each day’s use with a known concentration of the target gas. 

The instrument does not need to be calibrated unless it does not pass the bump test. 
To bump test the SC-04, you need:

Calibration gas cylinder

0.25 LPM fixed flow regulator

Non-absorbent tubing

Calibration cup

1. Confirm that the SC-04’s calibration gas value matches the concentration listed on the 

calibration gas cylinder as described on pg.47.

Table 9: Calibration Concentration Limits

Channel

Min. Cal. Gas 

Concentration

Max. Cal. Gas 
Concentration

Ammonia

8 ppm

400 ppm

Chlorine

0.15 ppm

10.00 ppm

Hydrogen Cyanide

0.9 ppm

30.0 ppm

Nitrogen Dioxide

0.50 ppm

20.00 ppm

Phosphine

0.05 ppm

20.00 ppm

Sulfur Dioxide

0.50 ppm

100.00 ppm

Summary of Contents for 04 Series



































































































Reviews: