RKI Instruments 04 Series Operator'S Manual Download

Page: 44 / 98

44 • Chapter 5: User Mode and Calibration

SC-04

11. The table below describes the 2 calibration outcomes.

Calibration Passed

Calibration Failed

1. The instrument indicates that the

calibration passed.

2. The instrument shows the current gas

reading.

3. If

MAX.SPAN

is set to

(default is

OFF

, see pg.88), the response

reading’s maximum adjustment is

displayed. A maximum span of 10.00

ppm indicates that the reading could

have been adjusted up to 10.00 ppm. If

the maximum span value is close to the

calibration gas value, the sensor should

be replaced soon.

The maximum adjustment is either

twice the calibration value or full scale,
whichever is lower.

4. Close the regulator.

5. The instrument continues to the

START

screen.

6. Remove the calibration cup.

7. Press and release POWER MODE to

enter Measuring Mode.

1. The instrument indicates that the

calibration failed.

2. Close the regulator.

3. Unscrew the regulator.

4. Remove the calibration cup.

5. Press and release POWER MODE to

return to the

A-CAL

screen in the

A-

CAL

menu.

6. See “Troubleshooting” on page 63.

PASS

A-CAL

SO2

5.10

A-CAL

ppm

SO2

10.00

MAX .SPAN

ppm

SO2

FAIL

A-CAL

ppm

Summary of Contents for 04 Series



































































































Search results

Summary of Contents for 04 Series

Reviews:

Related manuals for 04 Series

Brands by name

Popular brands

RKI Instruments 04 Series, Operator'S Manual

Search results

Summary of Contents for 04 Series

Reviews:

Related manuals for 04 Series

Brands by name

Popular brands