Rinnai RS100 Training Program Download Page 30

Page: 30 / 41

www.rinnai.us

PARA

Description

Range / Explanation

Factory

Setting

User

Access

Controller

application

type

(Outdoor

reset or RC

mode)

OFF

Outdoor reset mode: The RS100 doesn’t use the
room temp for operation. Boiler supply temp is
displayed (pressing the dial displays room temp).

Yes

Room Control/RC Mode: Controller fully enabled
(recommended)

Outdoor reset mode: The RS100

doesn’t use the

room temp for operation but it will be displayed

OFF or 3 is selected the boiler’s pump continuously operates. The boiler will fire based on the outside sensor.

NOTE: 1=Default at shipment, 3=Default at System Reset

Controller

effect type

(Parameter 3

must be set

to 1)

OFF

The boiler’s pump continuously operates. The
boiler will fire based on the outside sensor. Boiler
supply temp is displayed.

Yes

10-

500%

Do not use these settings

The boiler will operate based only on the
RS100’s area temperature sensor

NOTE: RC=Default at shipment, OFF=Default at System Reset

Unmixed (HC) Circuit Parameters

(continued)

N/A

OFF

/ON

This should not be altered

OFF

Yes

Summary of Contents for RS100










































Search results

Summary of Contents for RS100

Reviews:

Related manuals for RS100

Brands by name

Popular brands

Rinnai RS100, Training Program

Search results

Summary of Contents for RS100

Reviews:

Related manuals for RS100

Brands by name

Popular brands