Rinnai RINV25RC Installation Manual Download Page 6

Rinnai 

Split AC IM

OPERATION
DO NOT

 let the air conditioner run for extended periods when the humidity is very high or when doors or 

windows are left open� As this may result in an excessive operational loading and lead to product failure�

DO NOT

 cover or place articles on any part of this appliance�

DO NOT

 touch, operate or clean the air conditioner with wet hands� It may result in electric shock or 

product failure�

DO NOT

 insert hands or other objects through the air inlet or outlet while the appliance� It may result in 

electric shock or product failure�

DO NOT

  place  a  heater  or  other  heating  appliances  near  this  appliance,  always  ensure  sufficient 

ventilation when using this appliance and a heating appliance at the same time� Failure to do so may 

result in product miss-operation�

Turn main power off before cleaning. Failure to do so may result in fire, electric shock, or product failure.

DO NOT

 use solvents, abrasives or harsh detergent to clean any part or surface of this appliance or 

spray water or allow liquids to enter the indoor unit� The enclosure of the appliance and remote control 

can be cleaned using a soft, damp cloth and a mild detergent�

NEVER

 touch the metal parts of the air conditioner when you remove the air filter. It may result in electric 

shock or product failure�

DO NOT

 leave flammable materials near the appliance. It may result in explosion or fire.

If there is excessive noise, smell or smoke coming from the appliance, turn the appliance 

OFF,

 isolate 

the power supply and contact a service agent� 

DO NOT 

operate the appliance if it has been submerged into water due to flooding, contact a service 

agent. Failure to do so may result in electric shock, fire, serious injury, or product failure.

This appliance is 

NOT 

intended for use by persons (including children) with reduced physical, sensory 

or mental capabilities, or lack of experience and knowledge unless they have been given supervision or 

instruction concerning use of the appliance by a person responsible for their safety�

Children should be supervised to ensure that they do not play with the appliance�

The air conditioning system is designed to achieve consumer comfort� It is not designed for commercial 

applications required a controlled atmosphere (i�e� computer rooms, food preservation, etc�)

DO NOT 

block the inlet or outlet of air flow. It may result product failure.

DO NOT

 drink the condensate water drained from the appliance� This condensate is not potable and may 

present a health risk if consumed�

DO NOT 

expose people, animals or plants directly to the cold or hot discharge of the appliance� It may 

result in serious injury�

DO NOT

 mix the batteries for the remote control with other types of batteries or mix new batteries with 

used batteries� Failure to do so may result in product failure� 

STOP

 using the remote control if there is a 

battery fluid leak.

WARNING

WARNINGS AND IMPORTANT INFORMATION

Summary of Contents for RINV25RC

















Reviews: