background image

10

ASSEMBLY

Installing the Infeed Table

 

- Continued from page 9

3.  Insert the bar through the table’s end hole and under-

side of the table. Then re-attach the Spring Washer and 

Collar onto the Bar to secure it in place. FIG. 7.

4.  Hold the infeed table up to the machine while threading 

the depth of cut control bar into the Spacer Shaft (#137). 

FIG. 8.

5.  Install the infeed table by positioning it under the table 

cover rails and wind the depth of cut bar until the upper-

most line on the depth Scale is registered. See FIG. 15, 

page 12. Re-fit and secure the table cover rails, FIG. 9.

NOTE:  

These rails should not be fully tightened, as the 

table needs to slide up and down in order to adjust the 

depth of cut. As a guide, fully tighten the socket head cap 

screws and then back them off a 1/4 turn.

6.  See page 12 for instructions on adjusting the table.

FIG. 7

FIG. 8

FIG. 9

INFEED

TABLE

underside

view

WASHER

& COLLAR

BAR

SPACER SHAFT

DEPTH OF CUT

CONTROL BAR

DUST OUTLET INSTALLATION

1.  At the opposite, outfeed end of the machine, locate the 

Chip Ejector Hood (#194). FIG. 10. Attach the Dust Port 

(#195) to the outlet with the two hex Bolts provided. FIG. 11

FIG. 11

FIG. 10

CHIP EJECTOR HOOD

DUST PORT

CAP SCREW

COVER RAIL

DEPTH SCALE

Summary of Contents for 25-010

































Reviews: