RIKA REVO TOUCH, Operating Manual

Page: 7 / 24

|
7
EN
6
Dimensions
B
H
R-H
R-S F-S
F-H
F-
R-
T
Technical data
Dimensions
Height [mm] 1038
Width [mm] 520
Ccorpus depth [mm] 606
Weight
Weight without shell [kg] ~150
Weight with shell [kg] ~240
Flue pipe connection
R - Ø flue pipe outlet [mm] 100
RO - H original angle pipe connection height [cm] -
RO - T1 original angle pipe total depth [cm] -
RO - T2 original angle pipe distance to rear wall [cm] -
RO - T3 deapth from rear wall to middle of flue
pipe
[cm] -
RO - S original angle pipe side distance [cm] -
R - H rear connection height [cm] 15
R - S rear connection side distance [cm] 19
Fresh air connection
F - Ø diameter [mm] 50
F - H connection height [cm] 14
F - S side distance [cm] 23
Convection air connection
K - Ø diameter [mm] -
K - H connection height [cm] -
K - S side distance [cm] -
Amount of fuel
Nominal load Part load
Amount of fuel ~2,1 kg* ~0,6 kg*
Burn time at full pellet
hopper
up to ca. 22 h* up to ca. 53 h*
*Practical values may vary depending on pellet quality.
Note
Pellet consumption depends on the size of the pellets. The larger the pellet,
the slower the feed and vice versa.
Technical data
Heating power range [kW] 2,5 - 9
Room heating capacity (depending on house
insulation)
[m³] 50 - 240
Fuel consumption [kg/h] up to 2,1
Pellet container capacity* [l/kg] 59/~38
Electric supply [V]/[Hz] 230/50
Average electrical input [W] ~20
Fuse [A] 2,5 AT
Efficiency [%] 91,1
CO
2
[%] 14,3
CO-emission on 13% O
2
[mg/m
N
3
] 163
Dust emission [mg/m
N
3
] 9
Exhaust [g/s] 4,9
Exhaust temperature [°C] 175,3
Chimney draft requirement [Pa] 3
*The capacity in kg may deviate due to different pellet bulk densities.
The owner of small firing systems or the person authorised for the small
firing system is to keep the technical documentation and is to submit it to the
authorities or the chimney sweep on request.
Note
Please observe the national and European standards as well as local
regulations concerning the installation and operation of firing installations!
Packaging
Your first impression is important to us!
The packaging of your new stove provides excellent protection against damage.
However damage to the stove and accessories may still occur during transport.
Note
Therefore please check your stove on receipt for damage and completeness!
Report any deficiencies to your dealer immediately! Pay particular attention
during unpacking that the stone panels remain intact. Scratches to the
material can easily occur. Stone panels are excluded from the warrant.
The packaging of your new stove is environmentally neutral to a great extent.
Tip
The wood used in the packaging has not been surface treated and may
therefore be burnt in your woodburning stove (not in a pelletstove!). The
cardboard and film (PE) can be depolluted via the municipal waste collection
for recycling.
Electrical connection
The stove is supplied with an approx. 2 m long connecting cable with a Euro-
plug. This cable is to be connected to a 230 Volt / 50 Hz socket. The average
electrical power consumption is about 20 Watt in heating operation and approx.
150 Watt during automatic ignition. The connection cable must be laid in a way
that there is no contact to any sharp edges or hot surfaces of the stove.