20
Dimensions of DOMO PGI
793
1121
94
432
284
380
800
81
276
1160
100/150
50
Dimensions
Height
[mm]
1121
Width
[mm]
793
Corpus Depth
[mm]
432
Weight
Weight without shell
[kg]
~175
Weight with steelshell
[kg]
~190
Weight with stones
[kg]
~235
Weight with decor side panels
[kg]
~185
Flue pipe connection
Flue Pipe Outlet
[mm]
100
Rear Connection Height
[mm]
-
Rear Connection - side Distance
[mm]
-
Top connection Height
[mm]
1160
Top connection - Distance to rear wall
[mm]
94
Top connection - side Distance
[mm]
276
Fresh air connection
Diameter
[mm]
50
Connection Height
[mm]
380
Side Distance
[mm]
284
Convection air connection MULTIAIR
Diameter
[mm]
100
Connection height
[mm]
800
Side distance
[mm]
81
Amount of fuel
Nominal load
Part load
Amount of fuel
~2,3 kg/h*
~0,8 kg/h*
Burn time at full
pellet hopper
~20 h*
~60 h*
*Practical values may vary depending on pellet quality.
Note
Pellet consumption depends on the size of the pellets. The larger
the pellet, the slower the feed and vice versa.
Technical data for DOMO PGI
Technical data
Heating power range
[kW]
3 - 10
MULTIAIR-Output*
[kW]
0,5 - 1,9
MULTIAIR-Air volume*
[m
3
/h]
40 - 80
Room heating capacity (depending on
house insulation)
[m3]
70 - 260
Fuel consumption
[kg/h]
≤2,3
Pellet container capacity**
[l]/[~kg]
76/~50
Electric supply
[V]/[Hz]
230/50
Average electrical input
[W]
~20
Fuse
[A]
2,5 AT
Efficiency
[%]
92,7
CO
2
[%]
11,8
CO-emission on 13% O
2
[mg/m
N
3
]
46
Dust emission
[mg/m
N
3
]
18
Exhaust
[g/s]
6,6
Exhaust temperature
[°C]
135,5
Chimney draft requirement
[Pa]
3
*with a two meter MULTIAIR line in combination with RIKA design
outlet, values may differ in practice.
*
*The capacity in kg may deviate due to different pellet bulk
densities.
The owner of small firing systems or the person authorised for the
small firing system is to keep the technical documentation and is to
submit it to the authorities or the chimney sweep on request.
Note
Please observe the national and European standards as well as
local regulations concerning the installation and operation of
firing installations!
Packaging
Your first impression is important to us!
The packaging of your new stove provides excellent protection
against damage. However damage to the stove and accessories
may still occur during transport.
Note
Therefore please check your stove on receipt for damage and
completeness! Report any deficiencies to your dealer immediately!
Pay particular attention during unpacking that the stone panels
remain intact. Scratches to the material can easily occur. Stone
panels are excluded from the warrant.
The packaging of your new stove is environmentally neutral to
a great extent.
Tip
The wood used in the packaging has not been surface treated and
may therefore be burnt in your woodburning stove (not in pellet
stoves!). The cardboard and film (PE) can be depolluted via the
municipal waste collection for recycling.
Electrical connection
The stove is supplied with an approx. 2 m long connecting cable
with a Euro-plug. This cable is to be connected to a 230 Volt / 50 Hz
socket. The average electrical power consumption is about 20 Watt
in heating operation and approx. 150 Watt during automatic ignition.
The connection cable must be laid in a way that there is no contact
to any sharp edges or hot surfaces of the stove.
