37
NORMALBETRIEB / FLAMMENFÜHLZEIT
Das Steuergerät hat noch eine Funktion, über welche der korrekte Betrieb des Brenners festgestellt werden kann (Anzeige:
GRÜNE LED
leuchtet
andauernd auf).
Um diese Funktion zu benützen, muss man mindestens zehn Sekunden ab Brennerzündung warten und mindestens drei Sekunden lang auf den Entrie-
gelungsschalter des Steuergeräts drücken.
Nachdem der Schalter losgelassen ist, wird die GRÜNE LED zu blinken beginnen, wie in der hier folgenden Abbildung gezeigt.
Die Impulse der LED verursachen ein Signal, das ca. alle 3 Sekunden gegeben wird.
Die Anzahl der Impulse wird die Zeit festlegen, die der Fühler ab Öffnung der Gasventile für die Wahrnehmung der Flamme benötigt .
KIT INTERFACE ADAPTER RMG TO PC
Code
3002719
10 Blinken
Brenner geht nicht an und es
erfolgt eine Störabschaltung
37 - Falsche Elektrische Anschlüsse Kontrollieren . . . . . . . . Kontrollieren
Störabschaltung des Bren-
ners
38 - Defektes Steuergerät . . . . . . . . . . . . . . . . . . . . . . . . . . . Auswechseln
39 - Vorhandensein elektromagnetischer Störungen . . . . . . . Kit zum Schutz vor Funkstörungen verwenden
Kein Blinken
Brenner geht nicht an
40 - Kein Strom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Schalter schließen - Anschlüsse kontrollieren
41 - Eine Grenz-oder Sicherheitsfernsteuerung offen . . . . . . Einstellen oder auswechseln
42 - Leitungssicherung unterbrochen. . . . . . . . . . . . . . . . . . . Auswechseln
43 - Defektes Steuergerät . . . . . . . . . . . . . . . . . . . . . . . . . . . Auswechseln
44 - Kein Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Die handbetätigten Ventile zwischen Zähler und
Armatur öffnen
45 - Netz-Gasdruck nicht ausreichend . . . . . . . . . . . . . . . . . . Beim GASWERK nachfragen
46 - Mindestgasdruckwächter schließt nicht . . . . . . . . . . . . . Einstellen oder auswechseln
47 - Der Stellmotor schaltet nicht in die Position für min. Zündung Auswechseln
Der Brenner wiederholt pau-
senlos die Anfahrphase, ohne
daß eine Störabschaltung
eintritt
48 - Der Gasdruck in der Leitung ist dem am Mindestgas-
druckwächter eingestellten Wert sehr nahe. Der plötzli-
che Druckabfall beim Öffnen des Ventils bewirkt die
Öffnung des Druckwächters. Dadurch schließt sich das
Ventil sofort wieder, und der Brenner stellt sich ab.
Den Auslösedruck des Mindestgasdruckwächters
verringern. Den Einsatz des Gasfilters auswechseln.
Zündung mit Verpuffungen
49 - Kopf schlecht eingestellt . . . . . . . . . . . . . . . . . . . . . . . . . Einstellen
50 - Zündelektrode schlecht eingestellt . . . . . . . . . . . . . . . . . Einstellen, s. Abb. (C) S. 14
51 - Gebläseluftklappe falsch eingestellt, zu viel Luft. . . . . . . Einstellen
52 - Zu hohe Zündleistung . . . . . . . . . . . . . . . . . . . . . . . . . . . Verringern
Der Brenner erreicht die
Höchstleistung nicht
53 - TR-Fernsteuerung schließt nicht. . . . . . . . . . . . . . . . . . . Einstellen oder auswechseln
54 - Defektes Steuergerät . . . . . . . . . . . . . . . . . . . . . . . . . . . Auswechseln
55 - Defekter Stellmotor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Auswechseln
Bei Brennerstillstand Luft-
klappe geöffnet
56 - Defekter Stellmotor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Auswechseln
Im Falle des Abschaltens des Brenners den Brenner nicht mehrmals hintereinander entstören, um Schäden an der Installation zu vermei-
den. Falls der Brenner zum dritten Mal hintereinander eine Störabschaltung vornimmt, kontaktieren Sie den Kundendienst.
Sollten weitere Störabschaltungen oder Anomalien des Brenners auftreten, dürfen die Eingriffe nur von befugtem Fachpersonal entspre-
chend den Angaben in diesem Handbuch und gemäß den geltenden gesetzlichen Vorschriften und Normen durchgeführt werden.
ROTE LED eingeschaltet
mindestens 10 Sek. Warten
Entriegelungss-
chalter drücken
für > 3 Sek.
Signal
Pause
3 Sek.
Signal
SIGNAL
FLAMMENFÜHLZEIT
Diese Angabe wird bei jedem Anfahren des Brenners
aktualisiert. Nach der Lesung wiederholt der Brenner nach
kurzem Druck auf den Schalter des Steuergeräts den
Anfahrzyklus.
ACHTUNG
Wenn die Zeit > 2 s ist, so liegt eine verspätete Zündung vor.
Prüfen Sie die Einstellung der Hydraulikbremse des Gasventils
und die Einstellung der Luftklappe und des Flammkopfes.
1-maliges Blinken
0.4 Sek.
2-maliges Blinken
0.8 Sek.
6-maliges Blinken
2.8 Sek.
Signal
Störung
Mögliche Ursache
Empfohlene Abhilfe
ACHTUNG
Summary of Contents for RX 350 S/P
