Riello RLS 800/E MX, Installation, Use And Maintenance Instructions

Page: 35 / 92

33 20010309 GB
Maintenance
Pump
Delivery pressure must correspond with the table on pag. 19.
The depression must be less than 0.45 bar
.
Unusual noise must not be evident during pump operation
.
If the pressure is found to be unstable or if the pump runs noisily,
the flexible hose must be detached from the line filter and the fuel
must be sucked from a tank located near the burner. This meas-
ure permits the cause of the anomaly to be traced to either the
suction line or the pump.
If the problem lies in the suction line, check to make sure that the
filter is clean and that air is not entering the piping.
Filters (Fig. 42)
Check the filtering baskets on line 1) and at nozzle 2) present in
the system.
Clean or replace if necessary.
If rust or other impurities are observed inside the pump, use a
separate pump to lift any water and other impurities that may
have deposited on the bottom of the tank.
Nozzles
It is advisable to replace nozzles every year during regular
maintenance operations.
Do not clean the nozzle openings; do not even open them.
Flexible hoses
Check to make sure that the flexible hoses are still in good con-
dition.
Fuel tank
Approximately every 5 years, or whenever necessary, suck any
water or other impurities present on the bottom of the tank using
a separate pump.
Combustion
In case the combustion values found at the beginning of the inter-
vention do not respect the standards in force or, in any case, do
not correspond to a proper combustion, contact the Technical
Assistant and have him carry out the necessary adjustments.
Gas leaks
Make sure that there are no gas leaks on the pipework between
the gas meter and the burner.
Gas filter
Change the gas filter when it is dirty.
Combustion
In case the combustion values found at the beginning of the inter-
vention do not respect the standards in force or, in any case, do
not correspond to a proper combustion, contact the Technical
Assistant and have him carry out the necessary adjustments.
7.2.4 Safety components
The safety components must be replaced at the end of their life
cycle indicated in Tab. G. The specified life cycles do not refer to
the warranty terms indicated in the delivery or payment
conditions.
Tab. G
LIGHT OIL OPERATION
EN 267
Excess air
Max output
 
1,2
Min output
 
1,3
Theoretical max. CO
2
0 % O
2
Calibration CO
2
%
CO
mg/kWh

= 1,2

= 1,3
15,2 12.6 11.5

100
Fig. 42
D2012
GAS OPERATION
EN 676
Excess air
Max output
 
1,2
Min output
 
1,3
GAS
Theoretical max.
CO
2
0 % O
2
Calibration
CO
2
%
CO
mg/kWh

= 1,2

= 1,3
G 20 11.7 9.7 9.0

100
G 25 11.5 9.5 8.8

100
G 30 14.0 11.6 10.7

100
G 31 13.7 11.,4 10.5

100
Safety component Life cycle
Flame control
10 years or 250,000
operation cycles
Flame sensor
10 years or 250,000
operation cycles
Gas valves (solenoid)
10 years or 250,000
operation cycles
Pressure switches
10 years or 250,000
operation cycles
Pressure adjuster 15 years
Servomotor (electronic
cam) (if present) 10 years or 250,000
operation cycles
Oil valve (solenoid)
(if present) 10 years or 250,000
operation cycles
Oil regulator (if present)
10 years or 250,000
operation cycles
Oil pipes / couplings
(metallic) (if present)
10 years
Flexible hoses (if present)
5 years or 30,000 pressurised
cycles
Fan impeller 10 years or 500,000 start-ups