background image

 

page   84 / 85                                                                                   0MLMHTM16RUENUB 

9. 

Appendix B  - Optional remote commands 

 
Technical support personnel may modify the COMMAND that can executed from the standard “INV.OFF” remote 
input or from the optional remote input/output card. 
 

COMMAND 

Name 

Description 

Typical application 

Battery charge 

inhibition 

Disables the recharging of the battery, keeping the 
recharge current to a minimum, independently of the 
load. 

This is done with the contact kept closed; if 

reopened, the command is cancelled. 

When there is a generator, this allows 
its output power to be used only to 
supply the load and not also to 
recharge the battery. 

Inhibition of 

synchronization 

with backup 

mains  

 

Disables the use of the bypass line and the 
synchronization of the inverter. In the event of an 
overload or fault, the UPS blocks and the load remains 
unpowered. 

This is done with the contact kept closed; if 

reopened, the command is cancelled. 

To be used when the frequency of the 
generator or of the backup mains is 
highly unstable and it is thus 
preferred to inhibit the 
synchronization of the inverter. 

Battery 

disconnector 

contact  

Activates the battery discharging or disconnected alarm. 
To be used to indicate the opening of a battery switch 
located external to the UPS.

A closed contact must be 

provided when the external switch is opened. 

Displays the status of the battery 
disconnector. 

Standby ON 

Forces the selection of the UPS Standby-ON operation. 

This is done with the contact kept closed; if reopened, 
the command is cancelled. 

To be used when the load may 
support mains interference or 
frequency  variations and it is thus 
preferred to improve system 
efficiency. The load is powered if 
there is a mains power failure. 

Battery test 

Starts the automatic battery test when the UPS is in 
normal operation. 
Any automatic battery test underway is terminated 
immediately.

This is achieved by switching the contact 

from open to closed. 

Checks state of the battery. 

Battery test 

(with rectifier on) 

Starts the manual battery test that continues until a 
block command is received or until the full discharge of 
the battery. Terminates any manual battery test 
underway. 

This is achieved by switching the contact from open to 
closed. 

Checks state of the battery. 
NOTE: During this test the rectifier 
remains on with output voltage low 
in order to allow the supply of 
current by the battery and to prevent 
inverter shutdown after battery 
discharge. 

Manual battery 

charging 

Starts the “single first time recharge”. 
Terminates the first time charging underway. 

This is 

achieved by switching the contact from open to closed. 

Activates manual remote battery 
charging 

Activation of 

block on Bypass 

Bypass command by means of blocking the inverter as a 
result of switching onto the bypass line. 
NOTE: The command is only executed if the bypass 
line is present with correct values. 

This is achieved by 

switching the contact from open to closed. 

Load unpowered in the event of a 
mains outage. 
To be used for non-critical loads, the 
battery does not discharge during a 
mains power failure 

Inhibition of 

block on bypass 

Resets the bypass command. 

This is achieved by switching the contact from open to 
closed. 

Cancels the previous action and 
disables the inverter block. 

Inverter ON/OFF 

UNCONDITIONAL inverter block command (the 
command is executed even if there is no bypass line). 
The UPS only switches onto bypass if the bypass line is 
present (otherwise the load remains unpowered). 

This is done with the contact kept closed; if reopened, 
the command is cancelled.  

Load unpowered in the event of a 
mains outage. 
To be used for non-critical loads, the 
battery does not discharge during a 
mains power failure. 

Rectifier off 

UNCONDITIONAL rectifier blocks command. 

This is done with the contact kept closed; if reopened, 
the command is cancelled. 

Shuts down the rectifier and 
discharges the battery. 

 

 

Summary of Contents for Master-HP 160






















































































Reviews: