RIDGID PC116, Manual

Page: 7 / 400

Figure 2 – Machine Serial Number
The machine serial number is located on the side of the
cutter. The last 4 digits indicate the month and year of
manufacture. (10 = month, 19 = year).
Specifications
Nominal Tube Size
Cutting Capacity.........½" to 4" (12 mm to 100 mm)
Actual Cutting
Capacity .....................½" to 4.5" (12 mm to 116 mm)
Nominal Reaming
Capacity ...................½" to 2" (12 mm to 50 mm)
(optional accessory)
Max. Tube Length ....20' (6m)
Motor
Type .........................Universal
Voltage .....................100-120V 220-240V
Current .....................5.8 A 3.0A
Frequency ................50/60 Hz 50/60 Hz
Power .......................705W 705W
Refer to on-product serial plate for information specific to unit.
Roller Rotational
Speed.........................190/363 RPM for 220-240V,
225/385 RPM for 100-120V
Controls......................I-LOW/O-OFF/II-HIGH Switch
and ON/OFF Foot Switch
Weight ........................32 lbs. (14.5 kg)
Overall Dimension
L x W x H....................11.6" × 9.4" × 15.9"
(295 mm × 239 mm × 403 mm)
Operating
Temperature...............-4°F to 122°F (-20°C to 50°C)
Sound Pressure (L
PA
)* ...82.3 dB(A), K=3
Sound Power (L
WA
)*.......93.3 dB(A), K=3
* Sound measurements are measured in accordance with a standardized test per
Standard EN 62481-1.
- Sound emissions may vary due to your location and specific use of these
tools.
- Daily exposure levels for sound need to be evaluated for each application and
appropriate safety measures taken when needed. Evaluation of exposure lev-
els should consider the time a tool is switched OFF and not in use. This may
significantly reduce the exposure level over the total working period.
Standard Equipment
Refer to the RIDGID catalog for details on equipment
supplied with specific machine catalog numbers.
Selection of appropriate materials and instal-
lation, joining and forming methods is the responsibility of
the system designer and/or installer. Selection of improp-
er materials and methods could cause system failure.
Stainless steel and other corrosion resistant materials
can be contaminated during installation, joining and form-
ing. This contamination could cause corrosion and pre-
mature failure. Careful evaluation of materials and meth-
ods for the specific service conditions, including chemical
and temperature, should be completed before any instal-
lation is attempted.
To reduce the risk of ferrous contamination of stainless
steel, make sure that the rollers are clean and debris
free. Thoroughly clean with a stainless steel brush.
Change the cutter wheel and reamer before use with
stainless steel material. Best practice is to dedicate a
cutter for stainless steel.
Assembly
WARNING
To reduce the risk of serious injury during use, follow
these procedures for proper assembly. Switch should
be OFF and machine unplugged before assembly.
Bench Mounting
The machine can be mounted on a level, stable bench. To
mount the unit on a bench, unscrew the rubber feet at the
four corners of the machine base
(See Figure 16) and use
M8 bolts to retain machine to the bench. Tighten securely.
944-732-258.09_REV C 5
PC116/PTC-400 Power Tubing Cutter
NOTICE
Tube/Conduit Maximum Wall CutterWheel
Material* Thickness E-850 E-855
Cat. #66938 Cat. #66943
Carbon Steel 0.1" (2.5 mm) X
Stainless Steel 0.1" (2.5 mm) X
Aluminum 0.1" (2.5 mm) X
Copper 0.1" (2.5 mm) X
Plastic 0.23" (6 mm) X
* General guideline only.Material composition, hardness and other factors
affect ability to cut, wheel life, burr formation, etc