background image

13

 

Control Panel Users Guide

The Menu Error History screen displays any errors that have occurred, as well as 
the ignition cycle during which they occurred.

You can see what power cycle the system is currently on by going to the info 
screen.

P

ages 24 & 25 have a complete list of the systems error codes along with causes 

and solutions.

Make sure nothing is under the vehicle before performing 
calibration.  To Calibrate the system, select “Yes”.

The system will tell you what it is doing throughout the 
calibration process.

This screen will pop up after the system is calibrated.  Use 
the Manual Up & Down Buttons to set your ride height.   
After you get your ride height set, hold the #2 for 5 seconds.

P

2 Set” will pop up, select “OK”.

If you are not running level sensors, you will need to 
program all 3 presets.

The Menu Calibration screen allows the user to calibrate the system.

Though Calibration is not required for manual control of the system, Calibration is required to enable functionality of the 

P

resets.

During Calibration, the system learns specific characteristics of the vehicle into which it is installed.  This information is used by the 
system to accurately and efficiently reach preset destinations.

!ATTENTION!!!!!

 

  The vehicle 

MUST

 be running in order to calibrate this system

!

Only turning the key on will 

NOT

 work

!

 

Hooking it to a battery charger will 

NOT 

work

!

The vehicle must be running!

 

DO NOT RERUN CALIBRATION ON A SYSTEM THAT HAS BEEN PREVIOUSLY CALIBRATED.  IF YOU 
ARE HAVING A PROBLEM WITH THE SYSTEM, TRYING TO RECALIBRATE WILL MAKE IT DIFFICULT 
TO DIAGNOSE THE PROBLEM.

Summary of Contents for RidePROe5






















Reviews: