Ricoh FT2012+ Operating Instructions Manual Download Page 44

Page: 44 / 88

IS LIT OR BLINKING: ADD TONER

When the Add Toner

indicator blinks, it is time to supply toner

(copying is still possible). When the Add Toner

indicator is continu-

ously on, copies cannot be made until the toner bottle is replaced.

WARNING:

Do not incinerate used toner or toner containers.
Toner dust might ignite when exposed to an open
flame.
Dispose of the used toner containers according to
local regulations for plastics.

Note:

When you change the toner bottle, be careful not to touch
the blue material (OPC).

Note: Before setting the new toner bottle, shake it well at least 5 or 6

times.

Note: Do not remove the toner bottle before the Add Toner

indica-

tor comes on — toner could spill out.

Open the new toner bottle box
and take out the bottle.

Shake the new bottle well at
least 5 to 6 times.

HAT TO DO

SOM

G GOES

ONG

IS LIT OR BLINKING: ADD TONER

Summary of Contents for FT2012+

























































































Search results

Summary of Contents for FT2012+

Reviews:

Related manuals for FT2012+

Brands by name

Popular brands

Ricoh FT2012+, Operating Instructions Manual

Search results

Summary of Contents for FT2012+

Reviews:

Related manuals for FT2012+

Brands by name

Popular brands