Ricoh FT2012+ Operating Instructions Manual Download Page 24

Page: 24 / 88

ORIGINAL SETTING AND COPY DIRECTIONS

❐

When you use the following kinds of paper, set them into the bypass feed
entrance.

OHP sheets

When you copy onto OHP
sheets, set the originals and
OHP sheets as shown on the
right.

❐

When using OHP sheets, set one
sheet at a time into the bypass
feed entrance and open the copy
tray. Remove copies delivered to
the copy tray one by one.

Letterhead

When you copy onto letterhead,
set the originals and letterhead
as shown on the right.

Two-sided copies

When you make two-sided cop-
ies, set the originals and copy
paper for copying the reverse
side as shown on the right.

❐

Do not use paper that has been
copied onto by other machines.

Front side

Front
side

BASI

ORIGINAL SETTING AND COPY DIRECTIONS

Summary of Contents for FT2012+

























































































Search results

Summary of Contents for FT2012+

Reviews:

Related manuals for FT2012+

Brands by name

Popular brands

Ricoh FT2012+, Operating Instructions Manual

Search results

Summary of Contents for FT2012+

Reviews:

Related manuals for FT2012+

Brands by name

Popular brands