Rice Lake RL1200 Installation & Operation Manual Download Page 15

Page: 15 / 28

Installation

Rice Lake Weighing Systems

●

2.3.3 Trig Loop Assembly

Use the following steps to assemble the trig loop.

1. Insert the trig loop assembly to the end of the beam assembly. The ball handle should face towards the scale base.
2. Place the trig loop mounting plate on top of trig loop assembly prior to attaching to beam cap assembly.

Figure 2-15. Inserting the Trip Loop Assembly to Beam Assembly and Adding the Trig Loop Mounting Plate

3. Use bolts to secure the trig loop assembly to the beam assembly ensuring that trig loop washers are placed between

beam cap assembly and the mounting bolts..

Figure 2-16. Secure Trig Loop Assembly with Bolts

4. Ensure the trig loop assembly is centered horizontally. Adjustments can be made by readjusting the beam assembly.

The beam must not touch or rub the sides to ensure accurate weighments.

5. Once the trig loop assembly is centered, tighten the beam cap assembly and weight rack to the pillar.

Summary of Contents for RL1200




























Search results

Summary of Contents for RL1200

Reviews:

Brands by name

Popular brands

Rice Lake RL1200, Installation & Operation Manual

Search results

Summary of Contents for RL1200

Reviews:

Brands by name

Popular brands