Rice Lake RL-350-5 Technical Manual Download

Page: 12 / 32

RL-350 Series Wheelchair Scales

Visit our website

www.RiceLake.com

3.0

Operation

This section describes the front panel and includes procedures for operation of the scale.

Figure 3-1. Front Panel Keypad

3.1 Key Descriptions

The display has 10 front panel keys. Key functions are described in the table below.

The front panel keys are very sensitive, so only a gentle press is required.

Key

Name

Function

On/Off

Powers the scale on or off

LB/KG

Sends data out from the RS-232 port; Allows to toggle between kilograms and pounds providing that it is enabled in

Configuration

mode; Cannot toggle while in the

BMI

mode

Zero

Only functions if the current weight is stable and less than 2% of the capacity of the scale. Anything over 2% requires

a recalibration

Hold Release Displays most current weight value on the display and holds that value when the patient is off the scale. A second

press releases the weight value. Not active while in

BMI

mode

BMI

Pressing the

BMI

key enables access to the BMI (Body Mass Index) mode (defaults when scale is turned on). The

patient is gets on the scale, weight stabilizes and press the

BMI

key. The display then asks for the patient height to

calculate out the patient BMI.

TARE

Used to remove the weight initially of anything on the scale that shouldn’t be included in the total weight of the

patient on the scale

CLEAR

When using the BMI function, the display looks for a height entry. Pressing

Clear

changes this entry back to 190.0

cm (default) or 5 ft, 7.5 in.Once BMI is displayed, pressing the

Clear

key exits BMI

ENTER

Used to accept height in

BMI

mode; accepts the value of the parameter last entered and moves to the next stage

Pressing and holding Enter during startup will display ID. This is the first setup on entering into configuration mode

Up Arrows

Adjusts the value of the flashing digit/number

Adjusts height input (0.5 in/0.5 cm) while in

BMI

mode

Down Arrows Adjusts the value of the flashing digit/number

Adjusts height input (0.5 in/0.5 cm) while in

BMI

mode

Table 3-1. Key Functions

IMPORTANT

On/Off

LB/KG

Zero

Hold

Release

BMI

TARE

CLEAR

ENTER

Summary of Contents for RL-350-5

































Search results

Summary of Contents for RL-350-5

Reviews:

Related manuals for RL-350-5

Brands by name

Popular brands

Rice Lake RL-350-5, Technical Manual

Search results

Summary of Contents for RL-350-5

Reviews:

Related manuals for RL-350-5

Brands by name

Popular brands