Rice Lake Ishida OMNi-4000 Troubleshooting Manual Download Page 15 | Manualshive

Page: 15 / 40

background image

OMNi-4000 Error Codes and Troubleshooting

15.4 ERROR CODE (0400 - )

No.

Message

Symptom or Phenomenon

Check

OMNi-3000

0441 RIGHT SIDE TOP FILM DOOR IS

OPEN

Door open during operation

1. Upper-right side door is open.
2. Harness is damaged or short-circuited P-857 -> P-858 (No. B).
3. Harness damaged between P-857 and electromagnetic contactor.
4. Harness damaged between P-858 (No. B) and the upper-right side door.
5. Harness damaged between electromagnetic contactor and thermal relay.
6. Harness damaged between electromagnetic contactor and upper-right side door.
7. P-857 error or fuse(F1, F2, F3)
8. P-858 (No. B) error.
9. Electromagnetic contactor error.
10. Thermal relay error.
11. Upper-right side door error.
12. Rear Panel fuse(F21, F22, F23)

1150-0003

0442 LEFT SIDE TOP FILM DOOR IS OPEN Door open during operation

1. Upper-left side door is open.
2. Harness is damaged or short-circuited P-857 -> P-858 (No. A) -> P-858 (No. C).
3. Harness damaged between P-857 and electromagnetic contactor.
4. Harness damaged between P-858 (No. C) and the upper-left side door.
5. Harness damaged between electromagnetic contactor and thermal relay.
6. Harness damaged between electromagnetic contactor and upper-left side door.
7. P-857 error or fuse(F1, F2, F3)
8. P-858 (No. C) error.
9. Electromagnetic contactor error.
10. Thermal relay error.
11. Upper-left side door error.
12. Rear Panel fuse(F21, F22, F23)

1150-0006

0443 RIGHT SIDE DOOR IS OPEN

Door open during operation

1. Right side door is open.
2. Harness is damaged or short-circuited P-857 -> P-858 (No. B).
3. Harness damaged between P-857 and electromagnetic contactor.
4. Harness damaged between P-858 (No. B) and the right side door.
5. Harness damaged between electromagnetic contactor and thermal relay.
6. Harness damaged between electromagnetic contactor and right side door.
7. P-857 error or fuse(F1, F2, F3)
8. P-858 (No. B) error.
9. Electromagnetic contactor error.
10. Thermal relay error.
11. Right side door error.
12. Rear Panel fuse(F21, F22, F23)

1150-0004

0444 LEFT SIDE DOOR IS OPEN

Door open during operation

1. Left side door is open.
2. Harness is damaged or short-circuited P-857 -> P-858 (No. A) -> P-858 (No. C).
3. Harness damaged between P-857 and electromagnetic contactor.
4. Harness damaged between P-858 (No. C) and the left side door.
5. Harness damaged between electromagnetic contactor and thermal relay.
6. Harness damaged between electromagnetic contactor and left side door.
7. P-857 error or fuse(F1, F2, F3)
8. P-858 (No. C) error.
9. Electromagnetic contactor error.
10. Thermal relay error.
11. Left side door error.
12. Rear Panel fuse(F21, F22, F23)

1150-0007

Rev. Feb 2015

15/

40

Yellow highlights indicate updates

«
...
13
14
15
16
17
...
»

Summary of Contents for Ishida OMNi-4000









































Reviews:

No comments

Related manuals for Ishida OMNi-4000

Brand: Hagie Pages: 61

Brand: Nederman Pages: 89

Brand: Nederman Pages: 71

Brand: Nederman Pages: 131

Brand: X-Cite Pages: 2

Brand: quadient Pages: 188

Brand: Radarsign Pages: 16

Brand: TANACOM Pages: 27

Brand: iBACheck Pages: 2

Brand: Velp Scientifica Pages: 16

Brand: Velp Scientifica Pages: 2

Brand: Velp Scientifica Pages: 32

Brand: Velleman-Kit Pages: 32

Brand: YOKOGAWA Pages: 75

Brand: Össur Pages: 82

Brand: Hameg Pages: 39

Brand: Teac Pages: 1

Brand: Garelick Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands