Rice Lake ELS Series Installation Manual Download Page 14 | Manualshive

Page: 14 / 30

background image

Elevated Load Cell Stands

10

Visit our website

www.RiceLake.com

2.6.2 Conveyor Applications Less Than 3 Feet

1. Measure the length of the conveyor frame to determine the length for the support braces.
2. Attach one end of each support brace to one of the weigh stands.

Figure 2-6. Support Brace Install

3. Rest the other sides of the support braces on the other weigh stand.
4. See

Section 2.6 on page 8

to install the conveyor at this time.

The load cells must be in the same orientation before installing the support braces on the weigh stands.

5. Mark the locations where the bolts will be installed to the other weigh stand.
6. Drill a 7/16 inch through the top and bottom of the support braces.
7. Align the drilled holes of the support braces to the other weigh stand.
8. Install the support braces on the other weigh stand.

Note

«
...
12
13
14
15
16
...
»

Summary of Contents for ELS Series































Reviews:

No comments

Related manuals for ELS Series

1016-ANTPLATE Series

Brand: OBERON Pages: 2

Flex Collection Stand

Brand: Steelcase Pages: 16

Brand: JB Systems Pages: 2

Brand: d&b audiotechnik Pages: 10

Brand: Sandstrom Pages: 2

Brand: Skyvue Pages: 8

SURE-GRIP SG-VM-1

Brand: Zico Pages: 4

Brand: Unicol Pages: 5

Brand: CNC Router Parts Pages: 9

Brand: NCR Pages: 16

Brand: NCR Pages: 18

Brand: Electrolux Pages: 164

Brand: CONEN Pages: 5

Brand: Fujitsu Pages: 24

Brand: LG Pages: 16

Brand: NCR Pages: 5

Brand: Makita Pages: 28

Brand: Makita Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands