manualshive.com logo in svg

RHINO FC-0007, Operator'S Manual

Share
Download
RHINO FC-0007 Operator'S Manual Download Page 84

ASSEMBLY

SE6 05/05

Assembly Section 3-4

© 2005 Alamo Group Inc.

ASSEMBL

Y

TAIL WHEEL INSTALLATION (FIGURE Asm-R-0076). 

1.  Attach the Gauge Wheel Mount Weldment (1) to the Mainframe with four M14 x 35 Bolts (3), and Nuts (4).
2. Align Tail Wheel Beam Weldment (5) between pivot brackets located behind gearbox mount on the

Mainframe Weldment.  

NOTE

:  Long side of caster fork pivot tube is positioned up.

  Attach the Tail Wheel

Beam Weldment (5) to the Mainframe Weldment with one M16 x 90 Bolt (6), and Nut (7).  Slide Tail Wheel
Beam Weldment (5) into Gauge Wheel Mount Weldment (1) and retain with two M12 x 80 Bolts (8), and
Nuts (9).

3. Insert the Caster Fork Weldment (10) into the Tail Wheel Beam (5) and retain with Flatwasher (11) and

Cotter Pin (12).

4. Tighten all  bolts to the proper torque.

Summary of Contents for FC-0007

































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands