25
EcoNet Enabled 2-Stage Control™
If the ICC detects current in the start circuit
without current present in the run circuit, the
ICC will lockout the compressor to keep it from
continuing to operate and flash an
on the
dual -segment
Ds followed by a 0 .
IMPORTANT:
This mode of active
protection must be manually reset.
%XITING!CTIVE#OMPRESSOR0ROTECTION,OCKOUT
Three are three methods to reset the ICC after an active
protection lockout:
#YCLETHELINEVOLTAGETOTHEUNIT
#YCLE6!#TOTHE)##REMOVETHE2OR#
CONNECTIONTOTHE)##
0USHTHE4%34BUTTONDOWNWITHANINSULATEDPROBE
FORONE SECONDANDRELEASE
NOTE:
The ICC will attempt to start the unit
when the TEST button is pressed and released
NOTE:
The preferred method of resetting the ICC
ISTOPUSHTHE4%34BUTTONDOWNFORONE SECOND
Test and Fault Recall Modes
Test Mode (Test Button on the ICC)
s %NTER4%34MODEBYPRESSINGTHE50BUTTONWITHAN
INSULATEDPROBEFORFIVE SECONDSANDRELEASE
s4HE4%34MODECAUSESTHE)##TODOTHEFOLLOWING
2ESETSTHE)##FROMANYACTIVEPROTECTIONLOCKOUT
mode
2ESETSTHEMINUTEANTISHORTCYCLETIMER
%NERGIZESTHEUNITWITHOUTACOMMANDFORUNIT
operation
INSTALLATION
Active Compressor Protection Mode
Active Protection – Code 7
– Compressor open run circuit
s )FTHEMINUTEANTISHORTCYCLETIMERORSECOND
MINIMUMRUNTIMERISACTIVEAFLASHINGhCvORh#v
ISDISPLAYEDONTHEDUALSEGMENT,%$S ANDA
command for unit operation is present, TEST mode
causes:
!hCvTODISPLAYMOMENTARILYONTHEDUALSEGMENT
display
4HECOMPRESSORWILLSTARTANDTHEOUTDOORFANWILL
operate
4HEDISPLAYWILLCHANGETOASTEADYhCvORh#vTO
show the current command for unit operation.
NOTE:
If a command for unit operation is present
at the end of TEST mode will cause the unit to continue
to operate.
s )FNOCOMMANDFORUNITOPERATIONISPRESENT4%34
mode causes
!STEADYhCvAPPEARSONTHEDUALSEGMENT,%$S
4HECOMPRESSORWILLSTART
4HECOMPRESSORWILLTURNOFFAFTERSECONDS
Note: Entering TEST mode without a command for unit
operation will cause the compressor to run 5-seconds.
Fault Recall Mode
s %NTER
FAULT RECALL
mode by pressing the
UP
and
SELECT
buttons at the same time with insulated
PROBESFORFIVE SECONDSANDRELEASE
s 0RESS3%,%#4WHENANALARMISSHOWNFORSECONDS
will clear fault history. 00 no faults or history has been
cleared
s &#ISDISPLAYEDFORFAULTHISTORY0RESS3%,%#4TOSHOW
most recent fault. Continue to press UP to show other
alarms.
s %ACHFAULTISDISPLAYEDWITHTHEMOSTRECENTFAULT
displayed first.
s !MAXIMUMOFSIXINDIVIDUALFAULTSCANBESTORED
s !hvWILLBEDISPLAYEDWITHNOFAULTSARESTORED
s 4HE)##WILLAUTOMATICALLYEXITTHE
FAULT RECALL
mode after displaying stored faults
Summary of Contents for RA17 Series
