Rheem ASL-JEC Series, Installation Instructions Manual

Page: 23 / 52

Active Protection – Code L4 – Locked rotor
If the ICC detects the compressor has run less than 15 seconds for four (4) con-
secutive starts during the same command for unit operation, the ICC will lockout
the compressor to keep it from continuing to operate and flash a “L” on the dual 7-
segment LEDs followed by a “04”.
IIM MP PO OR RT TA AN NT T:: This mode of active protection must be manually reset.
4 4)) C Co om mp prre es ss so orr P Prro otte ec ctto orr T Trriip p
• If ICC detects a protector trip it will display a “P”. If protector doesn’t reset within 4
hours, the ICC display will change to “5”.
Compressor Protector – Code P – Protector Trip
5 5)) O Op pe en n S Stta arrtt C Ciirrc cu uiitt L Lo oc ck ko ou utt
• The ICC will display a flashing “L” followed by a flashing “06” when an open start
circuit condition occurs.
Active Protection – Code L6 – Compressor open start circuit
If the ICC detects current in the run circuit without current present in the start cir-
cuit, , the ICC will lockout the compressor to keep it from continuing to operate
and flash a “L” on the dual 7-segment LEDs followed by a “06”.
IIM MP PO OR RT TA AN NT T:: This mode of active protection must be manually reset.
6 6)) O Op pe en n R Ru un n C Ciirrc cu uiitt L Lo oc ck ko ou utt
• The ICC will display a flashing “L” followed by a flashing “07” when an open start
circuit condition occurs.
Active Protection – Code L7 – Compressor open run circuit
If the ICC detects current in the start circuit without current present in the run cir-
cuit, , the ICC will lockout the compressor to keep it from continuing to operate
and flash a “L” on the dual 7-segment LEDs followed by a “07”.
IIM MP PO OR RT TA AN NT T:: This mode of active protection must be manually reset.
E Ex xiittiin ng g A Ac cttiiv ve e C Co om mp prre es ss so orr P Prro otte ec cttiio on n L Lo oc ck ko ou utt
Three are three methods to reset the ICC after an active protection lockout:
1) Cycle the line voltage to the unit
2) Cycle 24VAC to the ICC (remove the R or C connection to the ICC)
3) Push the TEST button down with an insulated probe for one (1) second and
release
Note: The ICC will attempt to start the unit when the TEST button is pressed
and released
N No otte e:: The preferred method of resetting the ICC is to push the TEST button down
for one (1) second.
12.6 Test and Fault Recall Modes
T Te es stt M Mo od de e ((T Te es stt B Bu utttto on n o on n tth he e IIC CC C))
• Enter TEST mode by pressing the TEST button with an insulated probe for one
(1) second and release.
23
C
O
M
F
O
R
T
C
O
N
T
R
O
L
2
S
Y
S
T
E
M
™
C
O
N
T
R
O
L
W
IR
IN
G
6
continuing to operate and flash a “L” on the 7-segment LEDs followed by a “21”. Once
the outdoor ambient rises above 5
°
F the ICC will clear active protection automatically.
IMPORTANT:
This mode of active protection will automatically deactivate once the
outdoor temperature rises above 5
°
F. Wait until the outdoor ambient temperature rises
above 5
°
F before performing further diagnostics.
2)
High Pressure Control Lockout
•
If the HPC opens three (3) times during the same command for unit operation, the ICC
will lockout the compressor to keep it from continuing to operate and flash a L” on the 7-
segment LEDs followed by a “29”.
Active Protection – Code L29 – Open high pressure control
IMPORTANT: This mode of active protection must be manually deactivated.
3) Locked Rotor
•
The ICC will display a flashing “L” followed by a flashing “4” when a locked rotor
condition occurs.
Active Protection – Code L4 – Locked rotor
If the ICC detects the compressor has run less than 15 seconds for four (4) consecutive
starts during the same command for unit operation, the ICC will lockout the compressor
to keep it from continuing to operate and flash a “L” on the 7-segment LEDs followed by
a “4”.
IMPORTANT: This mode of active protection must be manually deactivated.
4)
Open Start Circuit Lockout
7
•
The ICC will display a flashing “L” followed by a flashing “6” when an open start circuit
condition occurs.
Active Protection – Code L6 – Compressor open start circuit
If the ICC detects current in the run circuit without current present in the start circuit, ,
the ICC will lockout the compressor to keep it from continuing to operate and flash a “L”
on the 7-segment LEDs followed by a “6”.
IMPORTANT: This mode of active protection must be manually deactivated.
5) Open Run Circuit Lockout
•
The ICC will display a flashing “L” followed by a flashing “7” when an open start circuit
condition occurs.
Active Protection – Code L7 – Compressor open run circuit
If the ICC detects current in the start circuit without current present in the run circuit, ,
the ICC will lockout the compressor to keep it from continuing to operate and flash a “L”
on the 7-segment LEDs followed by a “7”.
IMPORTANT:
This mode of active protection must be manually deactivated.
Exiting Active Compressor Protection Lockout
Three are three methods to reset the ICC after an active protection lockout:
1) Cycle the line voltage to the unit
2) Cycle 24VAC to the ICC (remove the R or C connection to the ICC)
3) Push the TEST button down for one (1) second and release
Note: The ICC will attempt to start the unit when the TEST button is pressed and
released
Note:
The preferred method of resetting the ICC is to push the TEST button down for one (1)
second.
7
•
The ICC will display a flashing “L” followed by a flashing “6” when an open start circuit
condition occurs.
Active Protection – Code L6 – Compressor open start circuit
If the ICC detects current in the run circuit without current present in the start circuit, ,
the ICC will lockout the compressor to keep it from continuing to operate and flash a “L”
on the 7-segment LEDs followed by a “6”.
IMPORTANT: This mode of active protection must be manually deactivated.
5)
Open Run Circuit Lockout
•
The ICC will display a flashing “L” followed by a flashing “7” when an open start circuit
condition occurs.
Active Protection – Code L7 – Compressor open run circuit
If the ICC detects current in the start circuit without current present in the run circuit, ,
the ICC will lockout the compressor to keep it from continuing to operate and flash a “L”
on the 7-segment LEDs followed by a “7”.
IMPORTANT: This mode of active protection must be manually deactivated.
Exiting Active Compressor Protection Lockout
Three are three methods to reset the ICC after an active protection lockout:
1) Cycle the line voltage to the unit
2) Cycle 24VAC to the ICC (remove the R or C connection to the ICC)
3) Push the TEST button down for one (1) second and release
Note: The ICC will attempt to start the unit when the TEST button is pressed and
released
Note: The preferred method of resetting the ICC is to push the TEST button down for one (1)
second.
3
Lowe r case “c ” ind icate s first stag e cooling oper ation
2) Second S tage Cooli ng Operation – W hen the IC C rece ives a co mman d for se cond stag e
cooling ope ration, an upp er case “C” is displ ayed on the 7- segmen t LEDs.
Uppe r case “C ” ind icate s second stage cool ing operation
3) Firs t Stag e Heat ing Op era tion - W hen the ICC recei ves a comm and for fi rst st age
heating operation, “h1” is displ ayed o n the 7-segm ent LEDs .
“h1” indicates first stage heating operation
4) Second Stage Heating Ope ration - W hen the ICC recei ves a co mmand for second st age
heating operation, “h2” is displ ayed o n the 7-segm ent LEDs .
“h2” i ndicate s second sta ge heat ing opera tion
5) Defrost Operation
– When the IC C starts a def rost cyc le, a lo wer case “d” is disp lay ed
on the 7-segm ent LEDs.
Lowe r case “d ” indi cate s defro st oper atio n (in hea ting m ode )
3-mi nute A nti-s hort Cycl e Timer