background image

INSTALLATION 

21 

REDUCING HEAT LOSSES 

The cold water line to and the hot water line from the water heater must be insulated in accordance with the 
requirements of AS/NZS 3500.4. The insulation must be weatherproof and UV resistant if exposed. 
 

ANODE 

The vitreous enamel lined cylinder of the water heater is only covered by the Rheem warranty when the total 
dissolved solids (TDS) content in the water is less than 2500 mg/L and when the correct colour coded anode 
is  used.  If  an  incorrect  colour  coded  anode  is  used  in  the  water  heater,  any  resultant  faults  will  not  be 
covered by the Rheem warranty. In addition, the use of an incorrect colour coded anode may shorten the life 
of the water heater cylinder. 
 
The  correct  colour  coded  anode  for  the  water  supply  being  used  must  be  selected  and  fitted  to  the  water 
heater  for  the  Rheem  warranty  to  apply  to  the  water  heater  cylinder  (refer  to 

“Water Supplies”

  on  page 11 

and the 

Anode Selection chart

 on page 11). The black anode is typically fitted as standard. 

 
 

Total Dissolved Solids 

Anode colour code 

– 40 mg/L 

Green 

40 

– 150 mg/L 

Green or Black 

150 

– 400 mg/L 

Black 

400 

– 600 mg/L 

Black or Blue 

600 

– 2500 mg/L 

Blue 

2500 mg/L + 

Blue (no cylinder warranty) 

 
 
If the water supply  has a TDS greater than 150 mg/L and a green anode has not been changed to a black 
anode, or if the TDS is greater than 600 mg/L and the anode has not been changed to a blue anode, there is 
the possibility the anode may become overactive and hydrogen gas could accumulate in the top of the water 
heater  during  long  periods  of  no  use.  In areas  where  this  is  likely  to  occur,  the  installer  should  instruct  the 
householder on how to dissipate the gas safely (refer to 

“Caution”

 on page 12). 

 

SADDLING - PIPE WORK 

To  prevent  damage  to  the  cylinder  when  attaching  pipe  clips  or  saddles  to  the  water  heater  jacket,  we 
recommend the use of self-drilling screws with a maximum length of 13 mm. Should pre drilling be required, 
extreme caution must be observed when penetrating the jacket of the water heater. 
 

Note:  If  the  cylinder  is  damaged  as  a  result  of  attaching  pipe  clips  or  saddles  to  the  jacket,  any 
resultant faults will not be covered by the Rheem warranty. 

 
 

Summary of Contents for 260 Litre









































Reviews: