when the machine is off, open the grounds drawer; remove the bag
from the hook ring; insert a new bag onto the ring and secure it in
position by means of the two side tongues;
insert the orange closing baffle to the bottom and lift the coffee
hopper, pay attention not to spill the content thereof;
rotate the dispensing slide closure and pull the canister by lifting it
slightly; to reassemble it, insert the rear bush into the motor gear
and the lower pin into the horizontal surface hole; the product
slides are plug-in mountedand removed from the canisters by
turning them clockwise;
after opening the machine, press on each side of the protection
carter (a) and remove it by letting the espresso nozzle through the
groove after removing it from the nozzle holder (b);
remove the ground grey conveyor by pulling it (c);
pull the brewer release button (d), lift and extract it;
remove the coffee canister; remove the two side covers from the
carter; turn the grinder ring nut (clockwise for a finer degree);
the effect produced by the regulation is shown by the drink
after three or four dispensing cycles;
see software
“
09.01.a. grinder
time”
and also
“
13.01. get an
espresso
selection”
;
remove the silicone tubes intended to dispense the product; turn
the orange ring nut clockwise; pull the mixing bowl body and
extract the mixer fan; you can now access the w-ring of the motor
shaft, the water inlet gaskets of the mixing bowl and the mixing
bowl gaskets , as already described by chapter 12.02. monthly;
remove the silicone tubes intended to dispense the product; turn
the orange ring nut clockwise and pull the mixing bowl body;
unscrew the crosshead by using a PH2 screwdriver and extract the
motor; the power supply wires can be removed without any tool;
remove the product canister; access the rear part of the machine;
extract the two small electric cables from the motor, hold the body,
push it to the bottom to release it from the bayonet connection of
the structure; the power supply wires can be removed without any
tool (observe the polarities);
the times specified by table 10.01. can be referred to as the times
functional for the machine and the products to be dispensed;
however, they can be adapted to the capacity of the
user’s
cups
(by changing
“time
water
N”)
and its tastes (by changing
“product
N”)
; please, never forget to make sure that the dispensing time of
the instant product is always lower than the one of corresponding
water;
(if accepted) dispensing starts as soon as the user presses a
selection key; the order in which instant products are poured into
the cup depends upon the values of delays (e.g. the one, the delay
value of which is zero, will be dispensed before the one, the value
of which is 40, dispensed four seconds after the user has pressed
the selection key); pay special attention when programming the
delays in dispensing a product and the water diluting it in the
mixing bowl; except for the instant coffee product, for which just
the opposite is applicable, it is recommended to dispense water
before the product to enable the latter to drop on the water film
already present in the mixing bowl for a better mix; espresso is
dispensed before and after any instant product by programming
the variable
“coffee
sequence”
;
c
d
b
c
a
Cino XS grande PRO VHO
by
MAN2100154 rel. 00 dated 04.11.2013 page no. 49 of 51 pages
www.rheavendors.com tel: 0039 02 966 551 fax: 0039 02 96 55 086 e mail: [email protected]
exclusive property of rheavendors group
13.04. empty the
grounds container
13.05. remove the coffee
hopper
13.06. remove the
instant canister
13.07. remove the coffee
brewer
13.08. regulate the
grinding degree
13.09. regulate the
ground dose
13.10. replace the o-ring
of mixing bowls
13.11. replace the mixer
motor
13.12. replace the mixer
motor
13.13. determine water
and product times
13.14. programme delays
