background image

4.5

 

MAINTENANCE SCHEDULE 

 
The following table summarizes the type and frequency of maintenance required.  Follow the manufacturer’s instructions 
for proper lubrication and detailed maintenance. For repairs, contact the nearest authorized service center. 
 

TYPE OF MAINTENANCE 

SERVICE FREQUENCY 

Check and clean obstruction from air intake at recoil starter screen 

Daily 

Check and clean obstruction from heat exchanger* 

Daily 

Check fuel level in gas tank—add if required 

Daily 

Check engine oil level—add if required 

Daily 

Check that reservoir oil level is within one inch below filler cap—add if required 

Daily 

Check that hydraulic oil is clean 

Daily 

Wash air filter pre-cleaner 

25 hrs. 

Change engine oil after first 8 hrs. ** 

50 hrs. 

Check battery electrolyte—add if necessary 

50 hrs. 

Check air cleaner filter—replace if necessary 

100 hrs. 

Check and clean obstructions from cooling fins and external surfaces 

100 hrs. 

Replace engine oil filter 

100 hrs. 

Check, clean, and replace spark plug 

100 hrs. 

Have cylinder head removed and cleaned (leaded fuel) 

100 hrs. 

Have cylinder head removed and cleaned (unleaded fuel) 

200 hrs. 

Replace reservoir filter and oil after first 50 hrs. *** 

250 hrs. 

Clean suction screen in reservoir 

250 hrs. 

Check coupling spider 

250 hrs. 

Grease wheel bearings 

500 hrs. 

Check ignition timing 

500 hrs. 

Check fuel filter in line 

500 hrs. 

Check valves and tappet clearance 

500 hrs. 

Lightly oil throttle cable 

500 hrs. 

 
* The hydraulic heat exchanger must always be kept clean and free of obstructions.  Check it daily before operating and 

frequently during use.  If debris builds up on the screen during operation, remove debris as soon as it is safely possible. 

 

CAUTION:

AN OBSTRUCTED HEAT EXCHANGER WILL CAUSE THE HYDRAULIC SYSTEM AND
ENGINE OIL TO OVERHEAT AND FAIL PREMATURELY.

 

 
** Change every 25 hours if engine is operated under heavy load or in high ambient temperatures. 
 
*** Change more often under heavy duty, high temperature, or high altitude applications.  When draining the oil, clean 

filler/breather cap and replace if damaged 

 

10 

 

 

Summary of Contents for HV1858C






















Reviews: