background image

13 

4

 

OPERATION 

 

4.1 

 

BEFORE OPERATING THE LIFT 

 

1. 

 

Review and follow all the safety precautions given in Chapter 1. 

 

2. 

 

Do not use the lift if it shows any signs of damage. 

 

3. 

 

Ensure that all bolts and nuts are fastened securely prior to operation.  

 

4. 

 

Ensure that the frame is square and that the lift sits level. (see Sec. 3.11) 

 

WARNING:

IF THE FRAME IS NOT SQUARE OR THE LIFT IS NOT LEVEL, BINDING MAY RESULT.
THIS CAN CAUSE PERSONAL INJURY AND/OR EQUIPMENT DAMAGE.

 

 

5. 

 

Never try lifting anything other than a boat with this lift. 

 

WARNING:

NEVER TRY TO USE THIS EQUIPMENT BEYOND ITS RATED CAPACITY.  THIS CAN
DAMAGE THE LIFT AND/OR BOAT RESULTING IN PERSONAL INJURY.

THE BOAT MUST BE PROPERLY POSITIONED ON THE LIFT BEFORE DOING ANY
RAISING OR LOWERING.  FAILURE TO DO THIS CAN CAUSE PERSONAL INJURY
AND/OR EQUIPMENT DAMAGE.

 

 

6. 

 

Never try to lift or launch your boat in rough water conditions.  This can damage your boat and/or the lift.  

 

7. 

 

Follow the Pre-Lifting Checklist before operating.  

 

8. 

 

Read and know the instructions and ensure that everyone understands the proper operating procedure. 

 

9. 

 

Understand the use of all the controls and connections provided with the power supply and the remote transmitter. 

 

4.2 

 

TESTING LIFT OPERATION 

 

After the lift installation is complete, it is important to test it for proper functioning before any load is applied.  Proceed as 
follows: 

 

1.

 

Use the up/down switch inside the control box to cycle the lift up and down.  Ensure that the hydraulic hoses are not 
binding or being pinched by any part of the lift. 

 

WARNING:

DO NOT STAND OR WALK ON THE LIFT PLATFORM WHILE IT IS IN ANY RAISED
POSITION.  THIS CAN CAUSE SERIOUS PERSONAL INJURY.

 

 

2.

 

The loading platform should move up and down smoothly without excessive stress or squeaking.  If there is excessive 
squeaking or binding, check that all pivot pins are properly lubricated. 

 

3.

 

After cycling the lift a couple of times, inspect all hardware to ensure that they are still secure and tight.  Also test the 
remote control and underwater lighting system. Ensure the hydraulic fluid level in pump reservoir remains up to the base 
of filler neck. 

 

4. 

 

Contact your authorized dealer if the hydraulic system fails to perform as described in this section.  Do NOT tamper with 
either system.

 

 
 

Summary of Contents for HL9000


































Reviews: