background image

 

 
 
 
 
The information contained in this document is subject to change. This document contains proprietary information, which is protected by copyright 
laws. All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language or program language 
without prior written consent of RFI Engineering B.V. 

 

 

 

 

 

Page: 18(

21)  

5.1  Retrieving the GSM configuration 

 

hibc ls -l -r config/gsm 

 

Grwp    25 Jan  1 00:00   |- gsm_device/ 
-rwp    26 Jan  1 00:00   |  |- dev "ttyS0" 
-rwp    27 Jan  1 00:00   |  |- baudrate "57600" 
-rwp    28 Jan  1 00:00   |  |- sim_pin "1234" 
-rwp    29 Jan  1 00:00   |  |- sim_pin2 "0000" 
-rwp    30 Jan  1 00:00   |  |- sim_puk "00000000" 
-rwp    31 Jan  1 00:00   |  |- sim_puk2 "00000000" 
-rwp    32 Jan  1 00:00   |  `- escape_ch "94" 
Grwp    33 Jan  1 00:00   |- call/ 
-rwp    34 Jan  1 00:00   |  |- allow_dailin "1" 
-rwp    35 Jan  1 00:00   |  |- call_idle_time "300" 
-rwp    36 Jan  1 00:00   |  `- call_connect_idle_time "60" 
Grwp    37 Jan  1 00:00   |- boot_sms/ 
Srwp    38 Jan  1 00:00   |  `- boot_sms_enable "enabled" 
Or--    39 Jan  1 00:00   |     |- enabled 
-rwp    40 Jan  1 00:00   |     |  |- boot_sms_nr "+316xxxxxxxx" 
Lrwp    41 Jan  1 00:00   |     |  `- boot_sms_objects 
Or--    42 Jan  1 00:00   |     `- disabled 
Grwp    43 Jan  1 00:00   `- sms_commands/ 
Srwp    44 Jan  1 00:00      `- sms_commands_enable "enabled" 
Or--    45 Jan  1 00:00         |- enabled 
-rwp    46 Jan  1 00:00         |  `- accept_cid "any" 
Or--    47 Jan  1 00:00         `- disabled 

 

5.2  Setting the GSM PIN 

 

hibc set config/gsm/gsm_device/sim_pin "5678" 

 
When  the  SIM  card  has  been  configured  to  accept  access  without  needing  a  PIN  code  the  G-
router will simply ignore the PIN code settings. Only when the SIM card has the PIN code option 
enabled will the G-router attempt to enter the PIN code. The unit will only attempt once to log in 
with  the  PIN  code  to  prevent  accidentally  blocking  the  SIM  card  when  a  wrong  PIN  code  has 
been entered.  
 

5.3  Getting the GSM PIN 

 

hibc get config/gsm/gsm_device/sim_pin 

 
Returns: 

5678 
 

5.4  Retrieving the GSM status: 

 

hibc ls -l -r status 

 

Gr--   100 Jan  1 00:00   |- gsm/ 
Grwp   101 Jan  1 00:00   |  |- gsm_dev/ 
-rw-   102 Jan  1 00:00   |  |  |- vendor "Motorola" 
-rw-   103 Jan  1 00:00   |  |  |- software "G24_G_0C.11.95R" 
-rw-   104 Jan  1 00:00   |  |  |- emei "357262000959333" 
-rw-   105 Jan  1 00:00   |  |  `- capability "GSM900 GSM1800 GSM1900 GSM850 MODEL=G24 " 
Gr--   106 Jan  1 00:00   |  `- gsm_status/ 
-rw-   107 Jan 28 16:22   |     |- sim_avaliable "SIM available" 

Summary of Contents for G-router






















Reviews: