background image

 

 
 
 
The information contained in this document is subject to change. This document contains proprietary information, which is protected by copyright 
laws. All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language or program language 
without prior written consent of RFI Engineering B.V. 

 

 

 

 

QIG_G-router_1.2.2 

Page: 19(

21)  

-rw-   108 Jan 28 16:22   |     |- sim_unlocked "SIM Unlocked" 
-rw-   109 Jan 28 16:22   |     |- network_available "Service Available" 
-rw-   110 Jan  1 00:01   |     |- network_name "vodafone NL" 
-rw-   111 Jan 28 16:22   |     |- network_signal "5" 
-rw-   112 Jan 28 16:22   |     |- network_roam "Camped on a home network" 
Lrw-   113 Jan  1 00:00   |     |- networks_available 
-rw-   114 Jan  1 00:00   |     `- ant_con "" 
Gr--   115 Jan  1 00:00   `- versions/ 
-rw-   116 Jan  1 00:00      |- rfios "Rose" 
-rw-   117 Jan  1 00:00      |- target "G-router" 
-rw-   118 Jan  1 00:00      |- buildnr "0235" 
-rw-   119 Jan  1 00:00      |- buildtag "RELEASE" 
-rw-   120 Jan  1 00:00      `- builddate "01/28/2008 15:51:05" 

 
The 

network_signal “5

 means this unit has excellent reception. The possible values for this 

field are:

  

 
0: G-router has no service. 
1: G-router has 1 bar of signal strength. 
2: G-router has 2 bars of signal strength. 
3: G-router has 3 bars of signal strength. 
4: G-router has 4 bars of signal strength. 
5: G-router has 5 bars of signal strength. 

 
 
The 

network_roam “Camped on a home network”

 means that this unit sits within its home 

network, i.e. it is not roaming. The possible values for this field are: 
 

camped on a home network. 
roaming on home network. 
roaming on other network. 

 
 

5.5  Setting idle-timer timeout 

The G-router is equipped with a configurable idle timer. This idle timer disconnects the GSM call 
when  there  is  no  data  being  received  from  the  remote  (dialer)  end. The  factory default  setting 
for this timer is 300 seconds (5 minutes). Every time you type a command from the dialer end 
the idle timer will be reset to 5 minutes. 
 
If  you  want  to  change  the  idle  timer  to  another  value,  for  example  600  seconds  (10  minutes), 
you would give the following command: 

 

hibc set /config/gsm/call/call_idle_time "600" 

Summary of Contents for G-router






















Reviews: