Respironics bilichek Service Manual Download Page 32

Page: 32 / 36

BiliChek Service Manual

1014988

12.0 Routine (Operator) Cleaning

The Bili

Chek

System is made of an easy-to-clean material

with a smooth, textured surface. One of the following clean-

ing agents is recommended for cleaning the exterior of the

HHU, Battery Charger Base, and Battery Packs:

♦

KleenaSeptic

♦

Cavicide

♦

70 to 90% Isopropyl Alcohol solution

♦

1% Bleach solution

Spray the cleaning agent on a soft damp cloth and wipe clean

the Bili

Chek

system. The same procedure can be used to

clean the display window.

Caution:

Clean the measurement tip with 90% or higher

Isopropyl Alcohol using a soft optical surface cleaning wipe.

WARNING:

Do not immerse any part of the system in water

or other liquid. If liquids spill onto the unit, wipe with a damp

cloth and allow to dry prior to using the system.

WARNING:

Do not attempt to clean and/or reuse the

Bili

Cal

Individual Calibration Tip.

13.0 Maintenance and Repair and

Replacement

13.1 Hand Held Unit (HHU) Measurement Light Bulb

Replacement

If the instrument bulb is not working and error code E01 or

E10 (refer to the troubleshooting section 11.4) is displayed, it

is necessary to replace the measurement light bulb. A Re-

placement Bulb Kit (RI P/N B800-22) is available from

Respironics or your local distributor.

WARNING:

The Bili

Chek

Non-Invasive Bilirubin

Analyzer is to be used only with the approved Replacement

Bulb Kit from Respironics. Do not over-tighten the lamp

cap.

♦

Remove the battery pack from the bottom of the HHU.

♦

Remove the protective label covering the lamp

assembly.

♦

Remove the lamp cap using a flat tip screwdriver.

♦

Grab the loop of the light bulb with forceps or similar

tool/instrument and gently pull to remove the lamp

assembly.

♦

Insert the replacement lamp assembly using caution

not to touch bulb with fingers. Be sure to place bulb

into socket firmly. DO NOT use the lamp

cap to tighten bulb into place.

♦

Apply the new lamp cap and protective label furnished

in the kit.

♦

Insert a fully charged battery pack into the bottom of

the HHU.

Summary of Contents for bilichek





































Search results

Summary of Contents for bilichek

Reviews:

Related manuals for bilichek

Brands by name

Popular brands

Respironics bilichek, Service Manual

Search results

Summary of Contents for bilichek

Reviews:

Related manuals for bilichek

Brands by name

Popular brands