Respironics bilichek Service Manual Download Page 28

Page: 28 / 36

BiliChek Service Manual

1014988

11.4 Hand Held Unit (HHU) Error Code List with Explainations

NOTE:

All sub errors are displayed in the date field unless specified otherwise in each section. See Illustration at the top of

page 32.

Error: E01 Calibration

Sub Errors Description

000001

Reference component out of range. Install a fully charged battery pack and try several calibrations with

new Bili

Cal

tips. If error persists, HHU requires service.

000002

Dynamic integration time out of range. Install a fully charged battery pack and try several calibrations

with new Bili

Cal

tips. If error persists install a new measurement light bulb and try calibration several

times. If the error still persists, the HHU requires service.

000004

Shape index above threshold. Try a fully charged battery pack and a new Bili

Cal

tip. If error persists,

HHU requires service.

000008

Peak pixel not found. Install a fully charged battery pack and try several calibrations with new Bili

Cal

tips. If error persists, HHU requires service.

008192

Stray Light Slope Error. Install a fully charged battery pack and try several calibrations with new Bili

Cal

tips. If error persists, HHU requires service.

016384

Mean of dark scan data above threshold. Install a fully charged battery pack and try several calibrations

with new Bili

Cal

tips. If error persists, HHU requires service.

NOTE: Firware

Version

≥

2.4/3.8

Only

Summary of Contents for bilichek





































Search results

Summary of Contents for bilichek

Reviews:

Related manuals for bilichek

Brands by name

Popular brands

Respironics bilichek, Service Manual

Search results

Summary of Contents for bilichek

Reviews:

Related manuals for bilichek

Brands by name

Popular brands