ResMed AirSense S10 Clinical Manual Download Page 27 | Manualshive

Page: 27 / 44

background image

24

Inspecting

Perform a visual inspection of the air tubing. If any visible deterioration is apparent (holes, tears or
cracks etc), the air tubing should be discarded and replaced. Slight discoloration may occur and is
acceptable.

Packaging and storage

Store in a dry, dust-free environment away from direct sunlight.

Storage temperature: -4°F to 140°F (-20°C to 60°C).

Reprocessing the water tub and air outlet

Disassembling

The following instructions provide guidance on how to correctly disassemble the cleanable water
tub and the air outlet.

1.

Remove the water tub from the device, open it and discard any remaining water.

2.

Hold the water tub base and then fully open the water tub lid and pull it away so that it easily
detaches from the base.

3.

Remove the water tub seal from the water tub lid by pulling it away.

4.

Locate the air outlet on the inside of the device.

«
...
25
26
27
28
29
...
»

Summary of Contents for AirSense S10













































Reviews:

No comments

Related manuals for AirSense S10

Brand: GBC Pages: 8

Brand: KAPSCH Pages: 57

Ettan IPGphor 3

Brand: GE Pages: 64

Brand: GE Pages: 56

Brand: GE Pages: 132

Brand: GE Pages: 16

Brand: GE Pages: 474

Tetrix 351 AC/DC Smart FW

Brand: EWM Pages: 117

Brand: 4iiii Pages: 36

Brand: 4iiii Pages: 34

Brand: 4EVAC Pages: 27

Brand: DBX Bushido Pages: 12

Brand: tayco Pages: 111

Brand: LA Audio Pages: 9

Brand: Task Force Tips Pages: 20

Brand: Launch Pages: 3

Brand: Launch Pages: 43

Brand: Launch Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands