manualshive.com logo in svg

REPLIGEN XCell ATF Series, User Manual

Share
Download
REPLIGEN XCell ATF Series User Manual Download Page 45

 
XCell

TM

 ATF System with C410:V4B Controller   

 

 

 

 

 

 

 

User Guide 

 

 

 

41 

 
 

 

The Operator can view C410v4B controller Warnings and Alarm conditions. All 
Alarms/Warnings are displayed with Time/Date stamping and full description of condition. 
Both Alarms and Warnings will activate the audible horn located inside C410v4B controller 
cabinet. An Alarm condition will automatically stop the pump cycling action, while a Warning 
condition allows the pumping cycling action to continue. Warning and Alarm conditions are 
described in the following section.

 

The Alarm screen will display parameters in the following tables:

 

Field

 

Description

 

Time

 

Indicates time of Alarm

 

Date

 

Indicates Date of Alarm

 

Text

 

Describes Alarm 

 

 

Button

 

Description

 

Horn Acknowledge

 

Press to turn off Horn

 

 

Select Highlight Warning/Alarm message and press to remove 

 

All Primary

 

All Primary Screen Buttons are displayed to navigate  to those screens 

 

 

 

 

E.

 

ALARMS 

Summary of Contents for XCell ATF Series































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands