REPLIGEN XCell ATF Series User Manual Download Page 10

Page: 10 / 126

XCell

ATF System with C410:V4B Controller

User Guide

3.0

Dimensions and Weight

COMPONENT

DIMENSIONS

DESCRIPTION

C410v4B Controller

inches

PNEUMATIC BOX

10.5

Includes all plugs and connectors.

ELECTRIC BOX

(Controls) Includes all plugs and connectors.

POWER BOX

10.5

(Power Separation) Includes all plugs and connectors.

Filtration Assembly

Fully assembled system

XCell™ ATF

4 System

6x10

Indicated dimensions are estimates for the Filtration

Assembly, as the connection to the bioreactor, the

connections to the controller and to accessories can

affect height and effective area.

XCell™ ATF 4MC

System

8x12

XCell™ ATF 6

System

8x12

XCell™ ATF

10lgcy

System

14x20

XCell™ ATF

10 System

14x20

XCell™ ATF

6 Single-

use Device

XCell™ ATF

10 Single-

use Device

C410v4B Controller

WEIGHT (Kg)

COMMENTS

PNEUMATIC BOX

~13

ELECTRIC BOX (Controls)

~23

POWER BOX

~12

(Power Separation)

Filtration Assembly

XCell™ ATF

4 System

Weight does not include the weight of any

liquid, filter or connection between the

Filtration Assembly and the vessel

XCell™ ATF 4MC

System

~14

XCell™ ATF 6

System

~14

XCell™ ATF

10lgcy System

~30

XCell™ ATF

10 System

~40

XCell™ ATF

6 Single-use

Device

~ 5

Does not include the weight of liquid and A2B

connectors

XCell™ ATF

10 Single-use

Device

~ 18

Summary of Contents for XCell ATF Series































































































































Search results

Summary of Contents for XCell ATF Series

Reviews:

Brands by name

Popular brands

REPLIGEN XCell ATF Series, User Manual

Search results

Summary of Contents for XCell ATF Series

Reviews:

Brands by name

Popular brands