Renogy MTS-SP100 Important Safety Instructions Manual Download Page 2

 

 

 

  

Important Safety Instructions 

 

 

 

 

     

 

Please save these instructions.

 

 

 

This manual contains important safety, installation, and operating instructions for the Renogy Pole 
Mount  hardware  system.  The  following  symbols  are  used  throughout  the  manual  to  indicate 
potentially dangerous conditions or important safety information.  

 

 

WARNING

:  Indicates  a  potentially  dangerous  condition.  Use  extreme  caution  when 

performing this task. 
 
CAUTION: Indicates a critical procedure for safe and proper operation of the system. 
 

NOTE: 

Indicates a procedure or function that is important to the safe and proper operation 

of the system.  
 

 

General Safety Information 

 

  Read all of the instructions and cautions in the manual before beginning the installation. 

 

  Do 

NOT

 attach solar panel to pole mount until mount is securely fit, and pole base has 

been secured.  
 

  Chance to strip nuts and bolts exists. 

 

  Multiple people for installation is suggested. 

 

  Do 

NOT

  substitute  parts  from  other  manufacture  ring  sources,  doing  so  may  void  the 

warranty and/or result in an unstable system 
 

  This system is 

NOT

 possess any compliance with residential structural codes and should 

not be used in place of a system that is, if so required by local regulations 

 

Installer Responsibilities 

 

  Installation compliance with any applicable codes which are in force at the installation site

 

 

  Installation compliance and compatibility with all system components and the environment 

including but not limited to roofing, system components, etc. 

 

 

  Verification that all project information is accurate

 

 

WARNING: 

This  equipment  should  be  installed,  adjusted,  and  serviced  by  qualified  electrical 

maintenance  personnel  familiar  with  the  construction  and  operation  of  the  equipment  and  the 
hazards involved. Failure to observe this precaution may result in bodily injury. Protective gloves 
and safety glasses should be worn during installation.

 

 

 

Summary of Contents for MTS-SP100

















Reviews: