background image

handle is moved to unlocked position 
the force exerted by the spring is re-
laxed and the gripping cam may be 
retracted by pushing the lifting shackle 
into body of clamp.  Refer to the Op-
eration Section of specific models of 
“Lock Closed” clamps for additional 
details.  Typical “Lock Closed” clamps 
are Models DG, FR and M. 
 
“LOCK OPEN ONLY” - normally used 
on “Hot Lift” clamps and consists of a 
manually operated “Lock Stop Pin” that 
is inserted when gripping cam of clamp 
is retracted and removed when clamp 
is positioned on the plate.  Tag line 
may be used to permit operator to re-
move pin from a greater distance from 
clamp.  Refer to the Operation Section 
of specific model of “Lock Open Only” 
clamps for additional details.  Typical 
“Lock Open Only” clamp is the Model 
RO. 
 
“LOCK OPEN-LOCK CLOSED” - an 
over-center spring loaded mechanism 
in which the spring exerts a force on 
the gripping cam when the lock handle 
is moved to the “Lock Closed” position.  
When the handle is moved to the “Lock 
Open” the gripping cam is maintained 
in the retracted position for ease in in-
stalling the clamp on a plate or mem-
ber.  The Model FRD contains individ-
ual “Lock Open” and “Lock Closed” 
mechanisms that must be operated 
separately.  Refer to the Operation 
Section of specific models of the “Lock 
Open-Lock Closed” clamps for addi-
tional details.  Typical “Lock Open-
Lock Closed” clamps are Models FRD, 
R, S, SD, SEA, SX, TL, TLA and the J-
Series. 
 
“LOCKING WEDGE” - is a fluted steel 
wedge that is driven in place with a
 

 

hammer.  The body of the wedge is 
positioned in a slot in the clamp body 
with the fluted edges contacting the 
member to which the clamp is being 
attached.    Refer to Operation Section 
of specific models of the “Locking 
Wedge”  clamps for additional details.  
Typical “Locking Wedge” clamps are 
Model A1, B1, B2 and PB. 
 
”LOCKING SCREW” - “Lock Screw” 
clamps depend on manually adjusting 
a screw to hold the gripping surface in 
place for lifting and removing the clamp 
from member being lifted.  Refer to 
Operation Section of a specific model 
of “Locking Screw” clamps for addi-
tional details.  Typical “Locking Screw” 
clamps are Models AC, ACP, NM, PC, 
SCP and SCPA. 
 
NON-LOCKING:  “Non-Locking” 
clamps have no mechanisms to aid in 
attaching or removing clamp from 
member being lifted.  It is necessary to 
have position of clamp maintained on 
the member being lifted until a properly 
applied force is exerted to the lifting 
shackle.  Refer to Operation Section of 
specific models of the “Non-Locking” 
clamps for additional details.  Typical 
“Non-Locking” clamps are Model AST, 
ASTL, BD, HR, HDR and WHSR. 

 

WARNING:  

A pointing out and notice 

of danger.  The purpose of a 
“WARNING” is to apprise the operator 
and all other affected persons of the 
existence of danger of which he should 
be but may not be aware and to enable 
the operator to protect himself and oth-
ers where applicable against such dan-
ger.  An attempt is made herein to 
warn against reasonable and reasona-
bly foreseeable danger in the proper 
use and possible reasonable misuse of 
RENFROE products described in this 
manual. 

Summary of Contents for R Clamp



























Reviews: