Reliance electric GV3000 Instruction Manual Download Page 62

Page: 62 / 91

713

Table 7.1 Wiring Signal and Control I/O to the Terminal Strip (Continued)

ÁÁÁÁÁ

Terminal

Number

ÁÁÁÁÁÁÁÁÁÁ

Description

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Parameters/Wiring Connections

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Wiring a Function Loss Input

Digital Input 5

(Function Loss)

The following parameters must be set:

P.026: Function Loss Response

A signal must be present at terminal 20 for the drive to be

able to start. See figures 7.1 and 7.2. The drive is shipped

from the factory with a jumper between terminals 16 and 20

which provides the signal. The function loss input should

be in series with the drive's external interlocks. In this case,

the jumper must be removed before the connections are

made. See figure 2.12.

Terminal 20 On = No Function Loss

(or from 16A and 20A on 15-60HP drives)

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Wiring a Run/Jog Input

Digital Input 4

(Run/Jog)

The following parameters must be set:

P.000: Control Source
P.020: Jog Speed Reference
P.021: Jog Ramp Accel Time
P.022: Jog Ramp Decel Time

Terminal 21 On = Jog Operation

StockCheck.com

Downloaded from StockCheck.com

Summary of Contents for GV3000

























































































Search results

Summary of Contents for GV3000

Reviews:

Related manuals for GV3000

Brands by name

Popular brands

Reliance electric GV3000, Instruction Manual

Search results

Summary of Contents for GV3000

Reviews:

Related manuals for GV3000

Brands by name

Popular brands