Reliance electric GV3000 Instruction Manual Download Page 57

Page: 57 / 91

Table 7.1 Wiring Signal and Control I/O to the Terminal Strip (Continued)

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Wiring Analog Outputs

010 VDC or 420 mA

Analog Output Reference
Regulator Common

The setting of parameter P.012 selects the terminal strip

analog output source (either speed or torque). Jumper J17

must also be set. See figure 2.11. The 420mA current

selection requires a power supply for operation. The power

can be sourced from the pulse tachometer supply, terminal

4 (15VDC), or from an external 15V power supply. Note that

the maximum supply current from terminal 4 is 250mA

(pulse tachometer and current source) at 15V. Terminals 9

and 11 are internally connected.

Terminal

Strip

Load

(Meter or Analog Input)

Connection to the negative side of the

power supply is only required

when an external 15V power supply is used.

StockCheck.com

Downloaded from StockCheck.com

Summary of Contents for GV3000

























































































Search results

Summary of Contents for GV3000

Reviews:

Related manuals for GV3000

Brands by name

Popular brands

Reliance electric GV3000, Instruction Manual

Search results

Summary of Contents for GV3000

Reviews:

Related manuals for GV3000

Brands by name

Popular brands